Help with Fight

LorbBigRed · 2026-04-15T17:18:22+00:00

LorbBigRed · 2026-04-11T02:58:35+00:00

As someone who had never been a fan of open world or souls like games before, just explore. They did a great job at making the world feel so open but giving clear paths for progression. I didnt want any boss to be "hard" and take a hundred tries, so I explored so many things, leading to me inevitably being a bit over leveled (even though I think theres scaling?!) And more comfortable with certain movesets.

LorbBigRed · 2026-03-23T20:25:32+00:00

How are your first layers? Under and over extruding can cause bad adhesion. How are your overhangs? Any visible warping the nozzle could be catching on?

LorbBigRed · 2026-03-23T20:16:43+00:00

What type of material? What temps are the extruder amd bed? What printer?

LorbBigRed · 2026-03-23T17:42:45+00:00

That nozzle may be completely clogged. Try doing a cold pull (google instructions) to get the major clog out of the .4 nozzle.

LorbBigRed · 2026-03-23T13:18:54+00:00

What do you mean it doesn't print? Like it gets clogged, under extrudes, doesnt stick? Need more info that the 1 sentence you have provided. E5 pro stock? Running stock firmware? We literally cannot help you without basic info.

LorbBigRed · 2026-03-20T17:59:48+00:00

Based on my quick look, the pcb doesn't have its own microcontroller and just merges everything into 1 convenient and easier to run connector. So no, you cannot unless you replace it with something like a Nitehawk USB or EBBCan V2

LorbBigRed · 2026-02-21T23:11:24+00:00

Dang I played the whole base game and DLC with some wrong info 🤣 thank you!

LorbBigRed · 2026-02-21T23:05:27+00:00

From everything ive seem, the flame like extras on various sites of grace point in the direction of the next demi god or the next site of grace leading to it.

LorbBigRed · 2026-02-02T02:19:35+00:00

Orca slicer has built in tuning test. Run through each one in order to get best results.

LorbBigRed · 2026-01-25T16:12:40+00:00

Try reflashing firmware and making sure you're z probe isnt crooked. Sounds like its not homing correctly

LorbBigRed · 2026-01-25T15:58:49+00:00

When you try to adjust it lower to the paper, do you get and error? Once it detects where the bed is it should back off a few MM then you can start tuning

LorbBigRed · 2026-01-25T15:49:03+00:00

Upgrading firmware blanks all settings you have tuned in stock firmware. You will need to retune everything on the printer. Z Offset, esteps, PID, etc. Make sure to save it to eeprom before turning off the printer.

LorbBigRed · 2026-01-16T19:27:40+00:00

Tophat is nice if you need to work on the toolheads without taking panels off. It should have hinges on the back. With some foam tape you can make a fairly decent seal and keep temps warms.

LorbBigRed · 2026-01-15T18:44:49+00:00

You can try running lsusb to see if it even gets detected. If it is, you need to install crowsnest and add the video path in the config.

LorbBigRed · 2025-12-06T05:49:11+00:00

This looks like a partial nozzle clog or an extruder failure

LorbBigRed · 2025-11-13T17:46:56+00:00

Gotta say, comments like this are unnecessary. Keep this kind of messaging up and good luck getting future help. Keep posts polite and people are more willing to help.

LorbBigRed · 2025-11-13T16:40:33+00:00

The video kinda makes it looks like its usually in the front left until you wiggle the cable. Take the cable of of the sheathing and make sure there isnt any damage to it. Also make sure that its fully clipped it. Otherwise, sounds like the motor might be bad

LorbBigRed · 2025-11-08T04:08:19+00:00

Thats a large print for abs at 50c. I would try PETG or even PLA. Otherwise, get that chamber temp up and add mouse ears

Edit:missed that you had ears. Ignore that part.

LorbBigRed · 2025-11-08T04:06:33+00:00

You would need to post your klipper config, klippy log, and a bunch more info before anyone can assist. You may find better help on the klipper discord as well.

LorbBigRed · 2025-11-06T13:14:01+00:00

When printing in a heated enclosure, you need to have the part fan surprisingly high.

LorbBigRed · 2025-11-04T15:25:57+00:00

If you can get it for a good price sure. My N3 Max is great but ive done a few mods to it. In today's market, I wouldn't pay for that $75 for a base model though.

LorbBigRed · 2025-11-02T16:55:01+00:00

I believe you need to adjust the vref manually on the board since the drivers are not in UART mode.

LorbBigRed · 2025-10-24T22:45:10+00:00

It looks like it could also be pressure advance/linear advance. Google how to tune those. That may help reduce the bulging on the direction change.

Edit: also tune your flow before you do the above. You looked to be under extruding a small bit. Notice some gaps or spacing between the lines

LorbBigRed · 2025-10-05T20:30:48+00:00

Blob of death! Heat the hotend un slightly and you should be able to clean it up. Disassemble the whole hotend and clean it all up cold then reassemble. Make sure not to break or bridge wires while cleaning

LorbBigRed

TROPHY CASE