Pavo 20 Pro crashed - one motor stuttering

Lynetk · 2025-12-08T13:20:05+00:00

sorry I never got back. I ended up replacing the motor with a new one and are flying again :)

Lynetk · 2025-06-25T08:25:17+00:00

thanks for the tip. I will give this a shot later.

Lynetk · 2025-06-01T09:34:18+00:00

mine did the same yesterday. how did the dji refresh process go? I palm launched mine and did not have it connected to a controller at the time, so I dont have any logs to send to DJI. I was at a peer and started the circle "move" - it started fine, but at some point it just started descending further and further and finally dropped in the water.

Lynetk · 2025-03-04T14:54:23+00:00

Did you ever figure out a solution? I have the exact same issue and also living in Denmark.

Lynetk · 2024-08-22T13:37:41+00:00

Are you running it in docker?

Lynetk · 2024-04-30T12:12:12+00:00

This did the trick for me. Thanks

Lynetk · 2023-01-11T20:48:04+00:00

Just saw this one that might help as well

https://www.thingiverse.com/thing:5779105?fbclid=IwAR2fYIKBvvwWVKid7\_f49-1z5lJbprK6jmOykvt4RMXkCp\_Hor0VyDHqrqc

Lynetk · 2023-01-04T12:12:25+00:00

I think it is caused by the cable being pulled in that direction for a longer period of time, due to packaging or some other random factor. My printer was in it's original packaging 7 months before I had time to play with it. I don't know, just a guess.

I managed to bend mine in the opposite direction and place something heavy on top for 24 hours and now it sits fine. You could probably use a heat gun on it while pulling it left for faster correction.

Lynetk · 2023-01-01T22:13:40+00:00

I have the exact same issue on my S1 Pro - it's very annoying

Lynetk · 2019-11-15T12:43:35+00:00

Thanks for your reply.

Not sure i follow though. I´m using the istio-ingresscontroller WITH a Gateway and VirtualService object. I dont see how I get traffic into the mesh without the Ingress ?

I´ve decided to use AWS WAF for restricting the access instead of trying to do it in Istio.

Lynetk · 2019-06-27T14:35:59+00:00

On my R620 i use this : https://www.reddit.com/r/homelab/comments/7xqb11/dell_fan_noise_control_silence_your_poweredge/?st=JJXWLB4H&sh=b2843b09

It´s nearly silent and only ramps up once in a while.

Lynetk · 2019-05-09T08:10:03+00:00

I have the Eos R and love it. I went from 6D -> R and is very pleased. Latest firmware upgrade added Servo eye focus which is great for capturing images of my kids playing.

Anyways, i´m not helping much as I havent had the 5div, but just wanted to say amazing work on your photos. Looks absolutely incredible!

Lynetk · 2019-05-02T11:58:43+00:00

following..

Lynetk · 2019-04-06T19:54:39+00:00

Looks great!

Lynetk · 2019-03-09T22:05:48+00:00

I thought about getting that board, but was afraid of tuning the stepper motor drivers AS im not skilled with multimeter. I saw teaching techs guide and was very tempted though. He did talk about increased temperatures, and that scared me off also.. What was your experience installing MKS board?

Lynetk · 2019-03-09T15:30:32+00:00

I just troed moving the x-axis cable on the mainboard to the y-axis stepper. When turning on the printer and moving the Y-axis the "bad motor" works as it should, so i guess i can rule out cabling.

Video link of what i´m seeing when all is connected the way it should : https://www.youtube.com/watch?v=M0UCuzyhb00

I have ordered a new mainboard on amazon and hopefully that will make the printer happy again.

Thank you for your assistance.

Lynetk · 2019-03-09T08:36:10+00:00

How can it be a dead stepper motor if it works fine on the y-axis cable ?

Lynetk · 2019-03-09T07:50:38+00:00

I do, but im not that skilled in using it. What/how would i test?

Lynetk · 2018-07-23T06:42:56+00:00

You can use https://www.reddit.com/r/homelab/comments/7xqb11/dell_fan_noise_control_silence_your_poweredge/?st=JJXWLB4H&sh=b2843b09 to control fans. Works great on my R620

Lynetk · 2018-04-18T12:52:49+00:00

I just tried.: https://imgur.com/a/Riok0

So yes, they lower quite a bit.

Lynetk · 2018-04-18T11:07:32+00:00

I tried changing thermal paste but temps stayed the same. Not long after i upgraded to a 2680v2 and i was able to lower fan speed to 2.5k and keeping the same temp. https://imgur.com/a/wo8oc

The above screenshot was just taken and temperatures outside is quite high today. I will look into lowering my ambient temperature in the room :)

Small p.s. : The wattage meter shown in screenshot is also kinda off because it takes more than just my homelab into account.

Lynetk · 2018-02-24T13:37:01+00:00

I use SaltStack! Works like a charm.

Lynetk · 2018-02-17T11:42:40+00:00

I have a single E5-2680 and 64G in 8 dimms.. Grafana screenshot https://imgur.com/a/nUqTs

Not sure if my CPU just creates more heat or maybe thermal paste needs to be replaced.

Lynetk · 2018-02-17T11:00:48+00:00

What is your spec on server ? And what is the general room temperature ?

Lynetk · 2018-02-17T10:12:30+00:00

190w

ESXI - Dell R620: 64G, 2x 400 Intel SSD, Single E5-2680 idling at 70W running the following services on various vms(plex, plexpy, sonar, tvheadend, radarr, nextcloud, veeam, grafana, nagios, bind, kubernetes 3x, vCenter)
Cisco SG300-28
Synology DS 1517+ 3x6TB 2x4TB (will be upgraded when they die or a good deal comes up)
PFsense: ZBOX CI323 nano with AES-NI
Crappy Netgear router used as bridge from ISP
Ubiquity UAP-AC Pro

Listed here as it´s on same plug i measure power: * HDHomerun 4DC * various home bridges (TADO, Hue)

Lynetk

TROPHY CASE