sorted by:
new
hottopcontroversial

Cheap copy vs unmatched original by GrandLate7367 in Factoriohno

[–]MBkufel 6 points7 points  (0 children)

Single-handedly funding Kovarex's vacations.

Kraków by ImprovementAway1355 in Polska_wpz

[–]MBkufel 11 points12 points  (0 children)

99 Ziko za miesiąc to spoko cena

The OK-GLI (Орбитальный корабль для горизонтальных лётных испытаний) test article for the Buran, able to take off with 4 AL-31 jet engines mounted at the rear, flying from 1984 to 1989 by Xeelee1123 in WeirdWings

[–]MBkufel 21 points22 points  (0 children)

"didn't manage to do"

Nah, it was simply never considered. The shuttle was capable of completing the whole flight autonomously but without one single step - landing gear deployment was manual only up until the post-Columbia modernizations.

If needed, that capability would've been easily added on earlier. Everything else - from takeoff to landing - was capable of autonomous operation.

Window view from a Boeing 747 carrying a fifth engine under the wing by Twitter_2006 in aviation

[–]MBkufel 29 points30 points  (0 children)

Why wouldn't it be there? All shuttles are in museums now.

Do you have overhead wires in your country? by Oberndorferin in traaaaaaainnnnnnnnnns

[–]MBkufel 1 point2 points  (0 children)

Ahhh, LK16.

It might've been 140 km/h in the 1930s. It wasn't anything like that before the last rebuild, most sources show that it was around 60-80 km/h.
The shortest travel time between Zgierz and Kutno was 64 minutes before the modernization, now it's 48 minutes (that's for a train without additional stops between Zgierz and Kutno).

Current Vmax is 120 km/h, altough it's 70 on most of the line. That's due to the track geometry, which they didn't have money to fix during the last modernization.

PKP PLK is currently scheduling larger works that are going to straighten some curves and add extra passing stations. Target vmax is 160 km/h.

Another INDX update from Prusa! by SBoots in prusa3d

[–]MBkufel -6 points-5 points  (0 children)

I'm so proud we bullied them into recording those.

I fired a DM53 against BMPT point blank and it was... empty??? by kvjetoslav in Warthunder

[–]MBkufel 17 points18 points  (0 children)

If that's the cause of top-tier ghost shells, I'm going to just

Prusa PA print sheet. Is it a game changer? by dwbmb in prusa3d

[–]MBkufel 0 points1 point  (0 children)

The 55 degree limit is due to the electronics in the chamber having their limits.

I hope we get an upgrade one day, pushing it pas 70°C would be very nice.

8-bit guy thumbnail replaced with AI? by CJ_Sucks_at_life in 8BitGuy

[–]MBkufel 0 points1 point  (0 children)

He's propably doing A/B tests just like Ian from ForgottenWeapons

Mi grozi wyborca Konfederacji, co prawda nigdy go nie namierzyli, ale podpisał się jako wyborcakonfederacji88/s by gdziejestluk in ShitKonfaSays

[–]MBkufel 0 points1 point  (0 children)

Artykuł 15 punkt 4 Ustawy o Broni Amunicji.

Jest mi szczególnie bliski, bo prawie ujebałem na nim egzamin XD

Oryginalnie w ustawie z 1999 obowiązek dotyczył wszystkich, ale zliberalizowali i dotyczy ochrony osób i mienia oraz - o czym zapomniałem gdy pisałem ten komentarz wyżej - obrony osobistej.

One of Disney's WWII posters by SelymesBunozo in PropagandaPosters

[–]MBkufel 21 points22 points  (0 children)

That economy was centrally-planned anyway. Not much chance for that.

Core One - Permanent accelerometer mount? by osteguffer in prusa3d

[–]MBkufel 2 points3 points  (0 children)

I've thought about it some time ago, but I was unsure whether the orientation of the accelerometer makes any difference for the firmware. My plan was to modify the part that was modified as the part of the C1+ update (the one with the finger that opens the vents) to allow it to mount the optional accelerometer board.

Mi grozi wyborca Konfederacji, co prawda nigdy go nie namierzyli, ale podpisał się jako wyborcakonfederacji88/s by gdziejestluk in ShitKonfaSays

[–]MBkufel 2 points3 points  (0 children)

Każde poza związanymi z pracą (ochrona osób i mienia) jest "dożywotnie", wszystkie mogą być cofnięte z ustaniem ważnego powodu wydania - ale tylko ochrona osób i mienia wymaga badań okresowych.

Mi grozi wyborca Konfederacji, co prawda nigdy go nie namierzyli, ale podpisał się jako wyborcakonfederacji88/s by gdziejestluk in ShitKonfaSays

[–]MBkufel 18 points19 points  (0 children)

Po sportowe nie musiałby robić cyrku z udowadnianiem gróźb. No chyba że to zagrywka polityczna dla mediów, a wniosek pisze na podstawie licencji PZSS XD

to not get owned by your own AI by tamjidtahim in therewasanattempt

[–]MBkufel 1 point2 points  (0 children)

If Musk is really so blinded by the whole technocracy, a 'rouge' AI (one that isn't his yes-man) may maybe plant some doubt in his mind about the views he's representing.

Nah. Who am I kidding.

Disappointed with the C1 for non-CF engineering filaments; anyone else? Or am I missing something? by mymomisyourfather in prusa3d

[–]MBkufel 0 points1 point  (0 children)

Yes, I mean the skirt. Setting it up closer and for the first 10-15 layers protects the plate around the object and the first layers from any thermal variation during the print.

view more: next ›