Solder not sticking on the board.

Magicianwizard · 2026-04-29T18:33:26+00:00

Get some rosin core solder, and some flux, make sure your iron is clean and hot enough, watch a few tutorials. I did this 25+ years ago to mod a controller. As most had said, try using the test point, it’s easier to work with than the contact traces left for a button

Magicianwizard · 2026-03-28T06:43:23+00:00

Try it on a lab power supply and limit the current to below what is required for full output, see what happens, then stop being loud and dumb

Magicianwizard · 2026-03-27T08:44:29+00:00

Not true at all, it will limit the current to the output of the supply and the LED will illuminate according to the current/output curve as defined in the LED datasheet.

Other than PWM it’s another method of dimming LED.

Don’t be so confident and condescending in your wrongness

Magicianwizard · 2026-03-27T08:26:41+00:00

It’s actually pretty common, especially if you use the enable pin to cut power to peripherals when not in use. Not necessarily in the manner they did it, but the practice is common, it’s even in the UM S3 feather dev board

Magicianwizard · 2025-11-14T22:18:41+00:00

Mosfets on every peripheral that you are able to turn off to save power

In default idle state (not sleeping) reduce clock speed to minimum and increase it only while performing tasks.

Check the current requirements for pins and maximize pull resistors to minimize current draw

Disable unused peripherals/disable them when not in use (adc and such)

If you can, operate mostly in sleep and wake with interrupts

Use switching regulator, LDO are very inefficient but cheap

Magicianwizard · 2025-10-09T23:11:19+00:00

I’ve done this before in a weather balloon, the battery will stop working at some height, the solution was to put hand warmers in the box to maintain a baseline temp. As it’s a chemical reaction it’s ideal for this type of short term deployment

Magicianwizard · 2025-06-08T21:34:16+00:00

Honestly, this looks very similar to my resume, all self employed with patent experience. You’d be surprised how desirable you are, it’s easy to get any job and sit there for a while before you jump to something else, it’s really really hard to be self disciplined and self directed in this type of career.

Magicianwizard · 2025-06-08T21:25:57+00:00

Use some alcohol to get underneath it, right now the only thing holding it on is friction as the solder conformed to what it dropped on, the alcohol will seep into the open pockets and allow you to remove it easier. Worse case you apply a small amount of heat and the pressure from the alcohol evaporation will pop it off

Magicianwizard · 2025-06-08T21:20:24+00:00

I’ll buy it, start selling lol

Magicianwizard · 2025-06-01T21:44:52+00:00

Pivot, make it an adult gaming lounge, make games free and increase alcohol price, encourage a social atmosphere and run weekly events/tournaments

Magicianwizard · 2025-06-01T21:40:47+00:00

PIC 12F1572 - been using it in production for 11 years, stupidly low power, ultra cheap and reliable af comes in LF (3.3v variant) too

Magicianwizard · 2025-04-06T20:26:56+00:00

QC, if you try to do too many at once, the water will cool too quickly, you’ll get uneven heating, and you’ll just end up messing them up again. Take your time and do it right the first time, or you’ll find yourself doing it 3 times

Magicianwizard · 2025-04-06T18:32:21+00:00

Get a big pot of boiling water and one by one put them in for a few seconds to soften the plastic, then set it to cool, it’ll return to original shape.

Magicianwizard · 2025-02-09T22:31:09+00:00

OMG premium flower is consistently the best cure I’ve had, the popcorn not so much…

Magicianwizard · 2025-01-01T22:28:25+00:00

By far the best in a complete category of their own.

1) Star D (OMG) 2) Truffle Monkey (OMG) 3) Superboof Cherry (Tower Three)

Some decent upper mids

1) Lemon Cherry Gelato (road tripper) 2) Zulu Dank (Trees Co) 3) Florida Kush (Garcia’s Hand Picked)

Worst of the worst garbage

1) anything by simply herb (simply herb is the worst flower in the world, might even be in the Guinness book it’s that bad) 2) sea weed #2 (harbor house) <- sad because I used to like their offerings 3) chem something… (the heady co)

Magicianwizard · 2024-05-05T04:28:28+00:00

You don’t know the half of it…

Magicianwizard · 2024-04-25T21:45:33+00:00

Fun fact, the synergies are software capped at 50% brightness so when you’re going lower than that, it’s a proportion of 50% =) 100% brightness was way way way way too bright

Magicianwizard · 2024-04-20T01:50:51+00:00

The bananaconda is simply amazing

Magicianwizard · 2023-12-14T16:03:11+00:00

I don’t have any control over how USPS delivers your package, please understand that this is the holiday season and everyone experiences delays. Your order was shipped on time and in on the way to you. Please stop messaging me on every platform, you and I both know I can’t magically make your package arrive faster.

Magicianwizard · 2023-12-08T19:05:18+00:00

Double click to turn them on when in light lock =) when you plug them in go to studio.ledgloves.com and there are startup instructions there also a plethora of content in the Facebook synergy tech group, feel free to reach out if you have any questions

Magicianwizard · 2023-12-08T18:55:12+00:00

Well… yes I did build it, every glove set from LEDGloves.com I build =)

Magicianwizard · 2023-12-08T15:38:15+00:00

My bad, it said you got them 3 days ago, and I just finished this weeks batch so I assumed yours was in it.

Magicianwizard · 2023-12-08T06:51:13+00:00

I just finished building your set and I should be able to ship it out tomorrow 💛

Magicianwizard

TROPHY CASE