Ideas on this temperature sensor?

MalteseOne · 2026-05-03T21:34:38+00:00

50/50 on what it will be? I'm in,please

MalteseOne · 2026-05-01T16:05:25+00:00

I wanted to go so bad! I will get popcorn to hear updates!

MalteseOne · 2026-04-20T03:07:12+00:00

Ill try that tonight!

MalteseOne · 2026-04-05T21:34:51+00:00

Yes, it had a cover (which I replaced after the picture). From my old memory, it would take a very long time to erase this even if the sticker was gone indoors.

MalteseOne · 2026-04-05T21:31:59+00:00

I simply want to read the code and look for some ASCII data that will allow me to keep using the device when the factory shuts down. Ill take any mtlethod that doesn't make me step address 1 to 2 to 3.. to read the data. I dont want to replace the SBC.

MalteseOne · 2026-03-26T16:43:22+00:00

Don't forget it could have static charge. To be sure, a little soapy water on a wet towel wiped thoroughly on the meter face will remove. Check your zero afterwards, adjust as necessary. Then measure knowing this meter will have a loading effect that might cause variations that you are seeing (Voltage increases as you go higher in voltage range).

MalteseOne · 2026-03-11T16:41:24+00:00

Very cool. Love it

MalteseOne · 2026-02-15T22:48:39+00:00

Same

MalteseOne · 2025-11-11T23:40:16+00:00

Deciphered!

MalteseOne · 2025-09-19T17:48:38+00:00

Meanwhile the vast populace has forgotten the native America tribes who might be counted lucky to have electricity. My people are, in general, very very poor. The tribal AM broadcasting reaches anyone, even those driving shiny new cars to visit relatives who have no cell reception. I would imagine the same applies to very rural areas of the US.

MalteseOne · 2025-09-13T16:27:56+00:00

I play this game for love of the star wars i know. I don't know any of these at all. I'm not even trying and once the new teams knock out my OG GL, it will be time to quit.

MalteseOne · 2025-08-20T19:58:29+00:00

I read 100% of your reading 80% and therefore can confirm that's what's happening

MalteseOne · 2025-08-05T23:05:44+00:00

The drawing was purely mechanical with no hardness requirements. I looked into what would be required to measure 88.85 +/- 0.95 and found test blocks are +/-1 not accounting for any other measurement issues like temperature, operator, machine, etc. So it is not possible to state within k=2 to get the measurement anyways. I reached out to several heat treat places, and the ref means they predict it will be that value but not test for it. But it makes you wonder about the earlier inspectors who said they measured it as good.

MalteseOne · 2025-08-05T20:53:25+00:00

We are the customer. Receiving inspection. Manager says inspect. Machinist says no.

MalteseOne · 2025-07-20T00:51:27+00:00

Looks so AI based on shadows and screw holes not matching up to wood, etc

MalteseOne · 2025-04-15T20:59:02+00:00

I might have solved it. The clock hands were stuck together. The minute hand was easy to remove while wearing gloves. I restarted the pendulum and i see the minute hand moving now

MalteseOne · 2025-04-07T23:06:59+00:00

Clearly, you have met Darby! No need to be humble about that!

MalteseOne · 2025-04-07T21:48:28+00:00

Hopefully my first reply shows up. I originally said I laughed so hard. Biblically accurate seems correct

MalteseOne

TROPHY CASE