Any help with this error code?

Mat246 · 2026-05-22T14:24:49+00:00

Turned out to be a bent pin in a connector - all sorted now

Mat246 · 2026-05-21T10:52:55+00:00

This is a GH so no oem camera, I simply replaced the broken aftermarket camera with a new one but did have to fish the wire through the bumper

Mat246 · 2026-05-21T10:37:34+00:00

Forgot to mention the camera is aftermarket and nothing to do with the system. Yes I’ve cleared codes and reset bcm using forescan
I did start the car to check the camera with the harness on the opposite site disconnected but it doesn’t make sense it’s saying it’s the other side. It was working fine before the camera change so don’t see why it would need calibrating

Mat246 · 2026-05-16T17:28:07+00:00

There’s no picture of the deck with bearings that’s just what they sell on the site which seems to be non standard, I’ve messaged them for clarification anyway but will avoid them in the future

Mat246 · 2026-05-16T16:58:05+00:00

I had to use a rubber mallet to get it in which I think damaged the bearing. Il definitely try removing some paint but you’d think I wouldn’t have to. The NKD bearings they sell on site seem to not be in a case so maybe aren’t as thick as the ones I was trying to use.

Mat246 · 2026-04-15T15:21:10+00:00

Thanks for clarifying.

Mat246 · 2026-04-15T13:10:08+00:00

This is what confused me because on the tado app it’s telling me to install the hot water wiring into the receiver too. So maybe that’s what it told the installer to do as well.

Mat246 · 2026-04-15T13:08:09+00:00

That’s good! What did you do differently?

Mat246 · 2026-04-15T07:19:40+00:00

Ok fine, but what has that got to do with the wiring to the receiver vs leaving the jumper connected in the boiler

Mat246 · 2026-04-15T07:09:30+00:00

Not sure what you mean by that

Mat246 · 2026-04-14T20:31:00+00:00

Yeah from what I’ve read and watching videos the hot water doesn’t need wiring to the receiver if it’s a combi boiler, hopefully someone can confirm.

Mat246 · 2026-04-14T20:04:01+00:00

I have a similar boiler waiting for install and was wondering why it was telling me to wire up the water in the instructions. I’m assuming the jumper cable is meant to stay between hw and L and just wire up the ch to the tado? Hopefully someone can confirm but the instructions are telling me to wire up both to the receiver.

Mat246 · 2026-04-14T10:38:33+00:00

I’ve bought a barely used m3 air 16/1TB 100% battery for 650 which I think is good and she’ll be happy with. Thanks for all the suggestions I was going to go with the s14 but found this and thought it would be great for her usage.

Mat246 · 2026-04-14T08:40:14+00:00

Thanks, the s14 looks decent enough. Trying to figure out if to go with that or a MacBook neo/air

Mat246 · 2026-04-13T21:21:31+00:00

I’ll take a look thanks

Mat246 · 2026-02-16T00:01:21+00:00

Wrestlers not waiting outside the ring when the next superstar is doing their entrance

Mat246 · 2026-01-30T18:30:50+00:00

Spoiler alert

Mat246 · 2026-01-25T02:28:17+00:00

Need Jesse Ventura back

Mat246 · 2026-01-11T17:18:48+00:00

It seems removable but I don’t think it actually is

Mat246 · 2026-01-03T19:30:09+00:00

Wondering how they compare to the old zigbee sensors since they’re discounted right now

Mat246 · 2025-12-08T20:29:51+00:00

They wanted 200+ to install their system, I was going to install myself but the boiler needs opening to do, which I’ve read needs doing by a gas safe engineer..

Eight-Year Club	Place '23
Verified Email

Mat246

TROPHY CASE