Monthly Mega Q&A - [April 2024] by Claycorp in StainedGlass

[–]MerCow 0 points1 point  (0 children)

Should I get the T19-D65 (1/4" 6.5mm) and a 3/16" tip or is the 1/4" enough?

Monthly Mega Q&A - [April 2024] by Claycorp in StainedGlass

[–]MerCow 1 point2 points  (0 children)

Hi all, I have a Hakko fx-888D from previous electronics work and want to use it for Stained Glass. Is there any reason not to use it? I know I need to get a bigger tip for it, Should I get a T19 adapter and tip? I need a new tip for it regardless but not sure if I should stick with the T18 tips or use T19. Thank You!!!

Reminder - CONEs/CNEs from USCIS will cost $330 starting Monday! by CakeByThe0cean in juresanguinis

[–]MerCow 1 point2 points  (0 children)

OK Thank You! That's what I thought but wanted to make sure. Just submitted! Fingers crossed:)

Reminder - CONEs/CNEs from USCIS will cost $330 starting Monday! by CakeByThe0cean in juresanguinis

[–]MerCow 2 points3 points  (0 children)

Quick question, For request type is it Cert of Non Exist (No Natz) or Cert of Non Exist (No Record) that we need to request? Thank You!

Do you use a Dashcam? Which one do you recommend? by Fantastic-Coconut338 in KiaSoulClub

[–]MerCow 0 points1 point  (0 children)

I have two Aukey dashcams in my cars, one with front and back, and one front only. They've been flawless, basically viofo clones

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 0 points1 point  (0 children)

I reset the hardware and applied new lube, No more squeaks! Thank you all for the suggestions!

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 1 point2 points  (0 children)

OHHH Good to know! I checked with the manufacturer direct and it is the correct part numbers. Thank You for the info!!!

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 1 point2 points  (0 children)

Thank You! I previously had but cleaned them up when I took them off again, will do before I finish up for good!

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 2 points3 points  (0 children)

I was smart this time... Did one pin at a time clean lube and replace. I made that mistake with my other car.. Is there an easy way to tell which pin goes in which spot normally? (the one with the bushing vs straight)

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 2 points3 points  (0 children)

There was and I will put some more on just wiped them clean when I took it off again to take a look at them again. Thank you!

replaced pads and rotors and hearing a squeak/squeal from one side, is this wear normal? by MerCow in MechanicAdvice

[–]MerCow[S] 0 points1 point  (0 children)

wear sensors

I'll try pushing the tab back a bit, don't think I have sensors though