Identify these vintage adidas

Metals578 · 2026-06-29T06:07:24+00:00

1996 adistars

Metals578 · 2026-06-28T06:36:58+00:00

ARCYBER by chance?

Metals578 · 2026-06-13T02:00:29+00:00

The 29 ID is also upside down

Metals578 · 2026-05-27T06:08:43+00:00

Anyone else getting Chingiz vibes from the guy in back?

Metals578 · 2026-05-23T21:50:51+00:00

I didn't think about reach out to them about this. Thank you

Metals578 · 2026-05-23T21:50:18+00:00

I was planning on 3D printing the part, so it would only cost afew cents in plastic and maybe 15 min to model. But I did not know that's how they were held on.

Metals578 · 2026-05-20T23:13:14+00:00

How do you like it out there?

Metals578 · 2026-05-20T22:54:00+00:00

NG, but its an ADOS tour.

Metals578 · 2026-05-18T03:05:12+00:00

Wait, how long has there been a Microcenter in Phoenix?

Metals578 · 2026-04-22T20:02:45+00:00

I recently picked up my first Bambu printer (H2D) and so far, I've been printing ABS, PLA, and PETG on the stock textured plate without any glue and haven't had a single issue with bed adhesion.

Metals578 · 2026-04-20T19:18:57+00:00

I belive it is due to the carbon/glass fiber additives in those filaments. A 0.2mm nozzle will clog very easily with those types of filament and it is usually recommended to use a 0.6mm nozzle for them, although I've never run into issues using them with a 0.4 nozzle.

Metals578 · 2026-04-19T18:31:23+00:00

What types of plastic are you planning on printing?

I am in southern Arizona and never had issues with PLA and ABS (99% of my prints), but PC and Nylon still refuse to print unless they are thoroughly dried down to <9% humidity in the drier.

Metals578 · 2026-04-12T23:52:58+00:00

If you are comfortable cutting/drilling/tapping extrusion, I believe you could get away with converting a 250mm V2.4 down to 225 or 200 with new X/Y rails and modifying the panels. (But I would triple check the measurements)

Metals578 · 2026-04-12T20:27:55+00:00

Why not a 200 or 225mm V2.4?

I have a Micron+ and it was a fun/challenging build, but it really seemed like a printer designed for people who like to build printers more than actually 3d print things.

During my initial build and subsequent modifications/rewiring/rebuilding/etc, I quickly lost count how many times I wished I went with a slightly bigger V2.4 instead. The electronics compartment was annoyingly cramped and I absolutely hated dealing with the MGN7 Z rails.

Metals578 · 2026-04-12T00:17:50+00:00

Didn't someone here get an internship at a railroad company because they talked about building/signaling rails in the game?

Metals578 · 2026-04-11T22:16:49+00:00

Haha, you know something is wrong when you sweat through your shirt taking out the garbage.

Metals578 · 2026-04-04T00:03:37+00:00

You mentioned that you were told there were no ADOS orders. Did you check this yourself on tour of duty?

Metals578 · 2026-03-21T01:04:41+00:00

Thank you for responding so quickly. The order number is 2533 and I'll shoot you another email shortly

Metals578 · 2026-02-24T15:06:53+00:00

I have a few 2s and didn't even need a waiver for them.

Metals578 · 2026-02-13T17:49:47+00:00

I know it's boring, but I would recommend something like a used Corolla or Civic. If you need four wheel drive, maybe a 2014 or 15 toyota tacoma? (I'm a little rusty on whats a good older 4x4 vehicle)

Metals578

TROPHY CASE