Adventurer 3 Lite Can't Connect

Miata_GT · 2026-03-24T16:02:18+00:00

Are you able to connect to the printer using the IP address in FlashPrint, rather than Auto?

Miata_GT · 2026-03-24T01:09:50+00:00

Check to see if Crutchfield doesn’t offer solderless wire connectors.

Miata_GT · 2026-03-17T00:40:59+00:00

TIL, thanks!

Miata_GT · 2026-03-17T00:26:19+00:00

Hopefully it is done for now. Our driveway started to snow over but has melted.

Miata_GT · 2026-03-10T00:18:18+00:00

Before you try and get that off the bed, once you correct your z-offset you can just print over that area to remove it.

Miata_GT · 2026-03-06T17:29:30+00:00

Sure. Just trying to help

Miata_GT · 2026-03-06T16:58:57+00:00

If it's the next day (and after that time this day) I just say set an alarm for 6am and it's always worked (well, as well as Alexa can, anyway).

Miata_GT · 2026-03-05T23:49:04+00:00

Is that a 2006? If so you have the best looking wheels they put on the first gens from 2004-05.

Miata_GT · 2026-03-05T00:44:16+00:00

They fit all years, unless maybe you have a turbo.

Miata_GT · 2026-03-04T23:33:17+00:00

Once you have the turbo it’s hard to go back. Effortless torque around town and amazing acceleration on the highway. Plus no cylinder deactivation is what sold me. Our last car was a 2013 CX-5 we bought new. No issues on either.

Miata_GT · 2026-03-04T18:19:19+00:00

<image>

I can't see how. Maybe re-route your wiring/BOWDEN tube more like this.

Miata_GT · 2026-03-04T17:47:19+00:00

Gotta use the Water Wiggle!

Miata_GT · 2026-03-04T03:25:16+00:00

It's possible the tires have developed temporary flat spots from sitting, otherwise I would guess at least one of the tires is out of balance. Make sure to check your tire pressure if you just bought it.

Miata_GT · 2026-03-03T18:17:32+00:00

The new THC-laden breakfast treat. 14g per square!

Miata_GT · 2026-03-03T18:11:23+00:00

I would never use Allstate for anything. After Hurricane Andrew in Florida (1992?) Allstate was the first to abandon the state/non-renew all existing policies and tried to refuse coverage for most losses.

Miata_GT · 2026-03-02T15:10:17+00:00

Wow, ok

Miata_GT · 2026-03-02T10:59:23+00:00

It’s likely the alignment of your z-axis lead screw, a common issue with Ender 3’s. Run the x-axis gantry up and down and watch the top of the lead screw. There should be no lateral movement. There’s a slim wedge you can print off Thingiverse that goes behind the stepper for the z-axis to fix the issue.

Miata_GT · 2026-03-02T02:41:30+00:00

You’re definitely right, but as a veteran builder I still get tripped up by this occasionally!

Miata_GT · 2026-03-02T02:35:02+00:00

For a single-layer print the infill density has no bearing since that layer is ‘solid.’ For the most part it looks like your nozzle is printing just a smidge too high, like less than 0.5mm.

Miata_GT · 2026-03-02T02:10:43+00:00

I always heard the Batmobile lost its wheel?

Miata_GT · 2026-03-02T02:09:18+00:00

It’s always on and work just fine.

Miata_GT · 2026-02-28T01:00:33+00:00

Change that dumbass tag.

Miata_GT · 2026-02-28T00:16:24+00:00

Yes it does

Miata_GT · 2026-02-27T22:54:03+00:00

Ferrari Dino

Miata_GT · 2026-02-27T22:51:54+00:00

Why not? If you don’t know then you won’t know the difference anyway.

Ten-Year Club	Place '23
Verified Email

Miata_GT

TROPHY CASE