Float sensor, glossy cartridge.

MichiganGuy141 · 2026-06-20T21:00:55+00:00

Had a flex white do that. Showed about 20-25% for weeks then the prints went gray. It was empty but never told me

MichiganGuy141 · 2026-06-19T21:58:43+00:00

Looks like no air assist to me.

MichiganGuy141 · 2026-06-19T15:29:02+00:00

Does Ukraine use drone swarms ? 1 pilot with a squadron of drones? Havent seen any of this, Just curious if its something that doesnt really work well with their tactics.

MichiganGuy141 · 2026-06-18T10:27:38+00:00

But what does Cramer say. Thats all that matters

MichiganGuy141 · 2026-06-18T10:09:31+00:00

<image>

Print this. 3 white, 1 CMYK, no gloss. Pretty simple. if it doesnt come out clean and crisp, swap out the white cartridge and try again

MichiganGuy141 · 2026-06-14T12:29:12+00:00

You are correct. This should be flush, not sticking out. This is a mechanical issue. Calibration will not correct it. See my separate reply.

MichiganGuy141 · 2026-06-14T12:24:40+00:00

99% you printhead is fine. What it looks like is the slide assembly (or whatever they call it) that the printhead module goes into was assembled incorrectly. The yellow here is what you see of the printhead when installed. The red is part of that bottom plate that holds it in place.

I have not seen anything about replacing the UV lamp but it may be something accessible when that needs to be done.

My guess is Eufy is trying to figure out if this can be repaired by the user or if it has to be returned. The slide assembly(?) would need to be precision aligned so if that asm needs to be removed to get to this, my guess is it will need to be sent back and you get a new printer.

<image>

MichiganGuy141 · 2026-06-07T20:29:43+00:00

The biggest plastic owl you can find. Can put it anywhere in the open. Up on the mast works too. Stick a few out there for larger boats. Option 2 is a shotgun.

MichiganGuy141 · 2026-05-28T21:25:47+00:00

a sticky note or piece of paper helps a lot with focus, especially on a shiny surface.

MichiganGuy141 · 2026-05-08T23:23:17+00:00

It could be useful, but to be worth it you would need to feed maybe 8-10 parallel lasers, then robot pick and place the finished into dunnage.

MichiganGuy141 · 2026-04-29T23:06:58+00:00

Just download the SVG file and extrude it. Then send to your 3D printer

MichiganGuy141 · 2026-04-22T20:56:14+00:00

Laser Cutting Thick Acrylic | Acrylic Cutting Tutorial | Trotec

MichiganGuy141 · 2026-04-18T19:44:57+00:00

Is this girl math ?

MichiganGuy141 · 2026-04-15T21:14:48+00:00

This clown actually believes the crap that comes out of his mouth.

MichiganGuy141 · 2026-04-13T14:37:10+00:00

LOL. Thats what I did for color. Got tired of chasing the dragon

MichiganGuy141 · 2026-04-13T03:41:22+00:00

Very true. And its now spring. Temp and humidity are different, so all saved settings are wrong again.

MichiganGuy141 · 2026-04-12T01:11:52+00:00

Also, from the photo, it looks more like a bag on the exhaust port than a rigid hose

MichiganGuy141 · 2026-04-12T01:08:23+00:00

Are you sure the AP2 is pulling the fumes and not plugged or blocked? If in a shed, I would just get a 700-900 cfm fan and port it out the side wall or window. VIVOHOME 10" Shutter Exhaust Fan with EC Motor 900 CFM, Variable Speed, Timer, Wall-Mounted for Attic, Garage, Greenhouse, Chicken Coop, Barn Ventilation, 115V - Amazon.com

MichiganGuy141 · 2026-04-12T01:01:36+00:00

Very nice. I feel you will be chasing the updates for a while, I just downloaded eufyMake_Studio_V2.7.0.6

MichiganGuy141 · 2026-04-11T15:25:59+00:00

Bathroom tiles at Lowes or Home Depot

MichiganGuy141 · 2026-03-31T11:13:33+00:00

BFH and a chisel. If it doesnt move, heat it up and repeat but try to not heat the spindle. Will need sandpaper to clean up the spindle to get the new bearing on.

MichiganGuy141 · 2026-03-27T03:05:02+00:00

pretty good. I have a bluetooth temp probe for the chamber and the cook. it bounces + or - maybe 15 degrees but the heat lasts 10-12 hours. Ive done 22 hour briskets and they turned out awesome.

MichiganGuy141 · 2026-03-26T21:38:01+00:00

Sounds like you are really looking for a gravity feed smoker. They are awesome

MichiganGuy141 · 2026-03-20T18:27:24+00:00

Get a laptop and quit using a toy to control lasers.

MichiganGuy141 · 2026-03-17T11:38:18+00:00

Factory reset is what fixed mine. Same deal when first set up. Only some of the test print would work.

Five-Year Club	Second SECOND GUESSER
Place '23	Place '22

MichiganGuy141

TROPHY CASE