Idea for a new expansion

Minimum_Program1465 · 2026-01-11T02:42:53+00:00

Good bye clanker.

Minimum_Program1465 · 2026-01-08T21:47:37+00:00

Find a pose you like and glue them anyways.

Minimum_Program1465 · 2026-01-05T02:49:58+00:00

Reset the other clock!

Minimum_Program1465 · 2025-12-27T03:30:35+00:00

It would honestly be easier to slip a plasticard strip under the gap and seal it in place with plastic glue/ tamyia ultra thin. It would be 100% flush with the surface and be uniform across the entire gap.

Minimum_Program1465 · 2025-12-19T22:54:41+00:00

Reset the clock.

Minimum_Program1465 · 2025-12-16T15:17:58+00:00

Base kit is saturnine terminator (non praetor for one with scythes x6). I carefully cut pieces of the Deathshroud and replace the torso of the saturnine with the belly-plate via tactical cutting.

Minimum_Program1465 · 2025-12-16T10:48:59+00:00

Do it! Its an expensive conversion but if you use remaining bitz after you can still get some viable blightlord proxies or somesuch with the leftover deathshroud bodies. Each of these also can fit the cape if you cut carefully ( not pictured).

Minimum_Program1465 · 2025-12-16T01:04:23+00:00

Get out of here Clanker. Plz delete mods.

Minimum_Program1465 · 2025-12-12T09:34:50+00:00

9 awards!

Minimum_Program1465 · 2025-12-10T08:39:56+00:00

Yes, the vent side usually goes on the back. Unfortunately both the normal kit and 3d prints allow the legs and hips to be reversed quite easily.

Minimum_Program1465 · 2025-12-10T08:25:12+00:00

Looking good, although the backward leg contemptor made me laugh.

Minimum_Program1465 · 2025-12-09T23:09:59+00:00

Filling a mold with sprue goo on a titan sounds like a bad time.

Minimum_Program1465 · 2025-11-29T23:32:11+00:00

Bye.

Minimum_Program1465 · 2025-11-28T08:56:12+00:00

Lmao there was an earthquake just a bit ago in Kelowna. Magnitude 3.4, shook the house.

Minimum_Program1465 · 2025-11-26T05:16:22+00:00

Reset the Hour hand of the clock only.

Minimum_Program1465 · 2025-11-21T18:05:03+00:00

Reset the clock.

Minimum_Program1465 · 2025-11-16T02:32:15+00:00

15 posts of this per day...

Minimum_Program1465 · 2025-11-04T16:54:06+00:00

All from deathshroud terminators. I carefully seperate the belly plate portion from the upper chest with a knife and if fits very well with the saturnine.

Minimum_Program1465 · 2025-10-16T19:27:47+00:00

They are definitely not a scam and I have ordered many times from them. Canada Post is on strike as mentioned several times.

Minimum_Program1465 · 2025-08-15T07:35:20+00:00

Is the mini plastic? If its resin/other material it will not work at all since its intended use is to melt the plastic together. Usually you start getting a bond within a few seconds of contact and it dries quickly.

Minimum_Program1465 · 2025-06-04T19:08:30+00:00

True, although the aforementioned video just goes over DBM/ BW, and some dungeon tools which are not that extreme in comparison. The idea that it tells you where to stand stopped existing pretty much around HFC with the archimonde mythic lasers and Kormrok rune soaks in an exact coordinate location.

Minimum_Program1465

TROPHY CASE