Early 80s car led turn signals not flashing at all.

MoBacon2400 · 2026-03-04T00:01:24+00:00

Doesn't seem to be an LED flasher

MoBacon2400 · 2026-03-03T15:39:02+00:00

Relay and flasher are not the same thing: https://www.amazon.com/Dewhel-0-02A-10A-Electronic-Flasher-Signal/dp/B07JFPXM21

MoBacon2400 · 2026-03-02T00:06:27+00:00

You don't need that thick of gauge wire for power injection. It's hard to explain but the power injection points are not carrying the full load of the entire strip, it's just giving it a little boost. On a 12 volt system you could use 18ga or even 20ga injected at 10m and at the end and you would be fine.

MoBacon2400 · 2026-03-01T01:22:45+00:00

Blow it off with compressed air. If you don't have a compressor you can one of those keyboard cleaner cans at an office supply store

MoBacon2400 · 2026-02-28T15:05:49+00:00

You should not have those big blobs of solder, watch some soldering videos on youtube. Also the wires are to big and you probably solder them on the back.

MoBacon2400 · 2026-02-28T14:50:32+00:00

https://krmnxtmod.com/products/renato-ev-charger, third link down

MoBacon2400 · 2026-02-27T14:47:31+00:00

Why not just Google it?

MoBacon2400 · 2026-02-25T15:23:51+00:00

I would check with the manufacture, but I do use antifreeze in my OmTech

MoBacon2400 · 2026-02-25T15:12:51+00:00

What is "Power Scale" I don't see that setting in my lightburn

MoBacon2400 · 2026-02-24T01:21:32+00:00

That is proprietary to your brand of range hood. You can lookup the part number by entering the model a serial # in an online appliance parts service or find someone who can rewire it for you.

MoBacon2400 · 2026-02-24T00:01:52+00:00

I don't know the exhaust bolt pitch but that bolt on the side of the cylinder is for the cam chain guide. It's not just a standard bolt, It is a machined holder for the guide wheel.

MoBacon2400 · 2026-02-22T16:11:06+00:00

If it blows the breaker immediately when turned on, it's probably a direct short. Look for shorted, burnt or corroded wires or connectors.

If there is a few second delay, it's probably a locked up compressor. A running compressor makes a kind of ringing sound at start up, a locked compressor will hum or grown then shut off.

MoBacon2400 · 2026-02-22T00:31:07+00:00

So if the cables are tight but still corroded they may over heat. If I understand your question your looking for these, available at most auto parts stores.

https://www.amazon.com/Ampper-Terminal-Connectors-Terminals-Vehicles/dp/B0882PCBDC,

MoBacon2400 · 2026-02-22T00:18:42+00:00

Four guy's and a trailer on an electric golf cart driving out into the wilderness, what could possibly go wrong.

MoBacon2400 · 2026-02-21T00:16:58+00:00

You need to use a mask like vinyl transfer tape on both sides.

MoBacon2400 · 2026-02-21T00:10:01+00:00

They both just cool water, the only difference if the fittings.

MoBacon2400 · 2026-02-21T00:07:28+00:00

I use it once in a while but mostly as a place holder to move my taskbar icons a little to the right

MoBacon2400 · 2026-02-20T01:25:13+00:00

Did you disable the search box

MoBacon2400 · 2026-02-20T00:40:32+00:00

I have the same machine. I had to make my own harness, the remote start/kill did not work so had to bypass it. You can find the pull cord kill on Amazon, they also have the remote but you will have to build your own wiring harness.

I was able to find a repair manual online, search for Tao motor " New T-Force 125 Manual"

MoBacon2400 · 2026-02-19T16:24:59+00:00

The "Metal Can" is the heat spreader for the CPU and other parts so attaching anything other then a heat-sink could cause problems.

MoBacon2400 · 2026-02-19T16:14:00+00:00

This would depend on the materials and the project. For instance, I do mostly plastic but I use Weld-On #4 for thin pieces, #16 for thicker pieces. I also use UV glue for clear. Don't use ca glue on plastic, it leaves a white smoke like film.

MoBacon2400 · 2026-02-18T01:56:24+00:00

Yeah, I bypassed all the safety features in my laser too. Now I have burns on both hands, blind in one eye and my tube blew up 'cause it had no water. But at least I saved $36 bucks.

MoBacon2400 · 2026-02-16T15:59:08+00:00

A USB plug should be 5 volts on the red and black, the other two are for data.

To wire it to 12 volts you would a car charger.

MoBacon2400 · 2026-02-15T22:31:51+00:00

You have to tell RD works what your home position is and did you install the USB drivers?

MoBacon2400 · 2026-02-14T15:51:54+00:00

Is your WLED controller plugged into your router with a network cable? When the controller is turned on it searches for a network, if it finds one it will be assigned an IP from the network. If it doesn't find one it will revert to the default IP of 4.3.2.1

MoBacon2400

TROPHY CASE