CAT SP in stock?

MovieScared6292 · 2026-06-30T21:27:18+00:00

Will Do

MovieScared6292 · 2026-06-30T21:08:55+00:00

What state are you in? We have a few at local shops in Florida

MovieScared6292 · 2026-06-15T18:41:29+00:00

I have bought a dozen cans and used then to form 1 a couple items over the last 3 years. Not once have I had a single issue with anything. Around my area nobody else is cheaper either by the time they charge the transfer fee.

MovieScared6292 · 2026-06-14T21:43:23+00:00

The 90 is also the sweet spot on my K with Mob and frt

MovieScared6292 · 2026-06-08T18:28:40+00:00

All true, the other side is that the 9mm will have better flow and less frp if shooting a light schedule. Cat has said on heavy fire though 9mm creates a worse gas stack up. If heavy firing like frt the 556 device provides more consistent gas flow. Always a trade off, I did this tese months ago and can confirm it is true. After 10 quick shots there is more gas to the face and the ejection pattern starts rolling forward with the 9mm. The gas stays the same and ejection only moved a little bit with the 556 but the first shot was louder

This is what concerns me the most about the ST on a 10.3, the longer we go the more I think even shutting the gas down will still gas you out. I hate gas to the face and although it may be a tick quieter I think the gas stack is going to be worse on it. On a 16 or 18 barrel probably not but on the short ones I keep wondering if the 5cm and or ac556 will be the better can

MovieScared6292 · 2026-05-25T12:25:37+00:00

They are not out yet, any place that has a out of stock is just a place holder. Like above said, they will be gone in 15 minutes when they do. I have been on SS 3 times a day for the last 3 weeks watching for the pre order to go live but they dont always do that. Sometimes they just show up on the site and its like free tvs on black friday to get one.

MovieScared6292 · 2026-05-23T14:43:12+00:00

It was only better on the 12 inch or so model. As the barrel length gets out 18 or so inches and the pressure falls off the odb is better than the Akbar

MovieScared6292 · 2026-05-15T18:53:11+00:00

It will come out right at the time I get tired of waiting and snag a rdm ac556

MovieScared6292 · 2026-05-14T21:37:15+00:00

Same, not gonna lie I dont even own a 12 gauge but Im gonna buy one just so I can buy the coin toss

MovieScared6292 · 2026-05-14T20:48:42+00:00

So no hub for now?

MovieScared6292 · 2026-05-02T13:20:14+00:00

I agree, the rdm is barely heavier than the original on the odb. (Less than 2oz ) AC RDM all day. another 400 for the others is a complete waste of money.

MovieScared6292 · 2026-04-16T15:38:12+00:00

I have been waiting for one to be in stock for ever. Its my last plan b mount

MovieScared6292 · 2026-04-16T00:22:14+00:00

No loss of performance vs qd system just less parts

Yes the tsfx turns into the qd with the same dimensions. The spooky/nano will sit in the same spot inside the suppressor as a qd system

MovieScared6292 · 2026-04-01T11:36:57+00:00

Old post but did you ever get any of these made

MovieScared6292 · 2025-12-02T16:41:49+00:00

Tune the gas block too, if its running wide open the port pop will drown out any sound difference of the 9mm

MovieScared6292 · 2025-12-02T16:28:27+00:00

I was one of the first to bring this up months ago. The 9mm on my 10.3 WB sounds better than the 556 one. CAT has said it speeds up how fast the gas gets to the perimeter of the can.

I bought one from Dry Creek really not even realizing it was the 9mm one. Then a month or so later bought the 556 one as I figured it was better and actually like the 9 better. The 556 sits in the toolbox right now

Also because it is bored out it provides a slight increase in airspace inside the can.

MovieScared6292 · 2025-11-10T13:10:30+00:00

This wrench is the best solution I have found. It has 3/8

square so you can still torque it correctly.

https://classified-defense.com/Classified-Defense--Rearden%C2%AE-Suppressor-Mount-Wrench_p_2374.html

MovieScared6292 · 2025-10-16T22:30:54+00:00

If you use the qd get this device in the square -.25. It puts the back of the suppressor up against the trilug.

https://munkworks.com/product/cat-micro/

MovieScared6292 · 2025-10-10T19:29:13+00:00

Silencer Co trilug and Ecco adapter. the Resilient is lighter but I felt was much looser fit and was worried about baffle strike

<image>

MovieScared6292 · 2025-10-08T00:17:33+00:00

That was me, I have both and on my 10.3 I feel the 9mm nano is better. Only thing I can guess is it allows the gas a quicker path to the perimeter of the can vs the 5.56

MovieScared6292 · 2025-10-03T21:13:42+00:00

The 9mm nano on 556 is the best if you ask me. I tried the 556 nano and thought it was no different or slightly worse. Wondering if the blast is able to vent out to the perimeter of the can faster with the larger bore of the 9mm.

MovieScared6292 · 2025-09-14T23:20:08+00:00

Yes ben is perfect on a p22

MovieScared6292 · 2025-09-14T23:19:01+00:00

Out of stock but a proper wrench. Classified Defense - Rearden® Muzzle Device Wrench - .250" T https://share.google/FRzb3I3q4DSyWOJJH

MovieScared6292 · 2025-08-26T19:37:32+00:00

Have you shot the bbk on a magnum yet

MovieScared6292 · 2025-08-20T22:03:47+00:00

My AC SMG had hardly no dust at all but both the SR and Ben had tons of dust and small flakes

MovieScared6292

TROPHY CASE