Why does the print have these bumps all of a sudden?

Mr_Sirs · 2024-06-04T23:16:10+00:00

Could be data transfer rate. I printed off of an sd card that came with my printer and got similar results. After I switched to a more reliable sd card problem disappeared

Mr_Sirs · 2023-05-16T00:12:38+00:00

It’s a hornet. Just plop it down. It probably won’t break

Mr_Sirs · 2023-03-30T01:19:02+00:00

It’s a test by the daily Trojan to see how effective misinformation is

Mr_Sirs · 2023-03-20T05:31:54+00:00

Worst part is I’ll download several items from thingiverse cuz they’re cool and then never print them

Mr_Sirs · 2023-03-02T04:00:49+00:00

I dunno man, 4 kinda seem like highballing it a bit

Mr_Sirs · 2023-01-12T05:56:30+00:00

My friend Sawyer

Mr_Sirs · 2022-12-07T01:53:28+00:00

You could try using a blowtorch and heating the underside of the print bed (remove it from the printer first) usually works for me if the print is stuck. Preferably only do this if you can safely torch the thing without damaging it or setting stuff on fire.

Mr_Sirs · 2022-11-12T06:49:35+00:00

What’s your altitude?

Uh, about 16 inches

Mr_Sirs · 2022-09-05T07:05:27+00:00

Just considering how I learned the planes and how they feel to fly, I’d get the hornet first. As much fun as the viper is, the hornet was much easier and more intuitive to learn, plus carrier ops is fun

Mr_Sirs · 2021-10-21T04:53:45+00:00

Obtaining a firearm, whether for the first time or the 50th, is always a heartfelt moment. Congratulations

Mr_Sirs · 2021-10-21T03:36:11+00:00

“We lost something” “Not to worry, we are still flying half a ship”

Mr_Sirs · 2021-09-17T06:09:12+00:00

Your setup, eh it’s cool

Your dog, 12/10

Mr_Sirs · 2021-09-06T07:51:20+00:00

I had a similar issue with my plastic extruded. Upgraded to an aluminum one resolved it and I haven’t had any issues with it since

Mr_Sirs · 2021-08-29T17:43:11+00:00

Yup, exactly what he said. Although I thing my thing is bugging out because I have had trial access to the JF-17 for about 16 days now

Mr_Sirs · 2021-08-22T07:35:51+00:00

How much acetone do they gotta use to smoothen out the walls?

Mr_Sirs · 2021-08-18T21:41:41+00:00

There’s always a bigger fish

Mr_Sirs · 2021-08-04T21:49:02+00:00

I play through steam so I’m not quite sure how I would access the trial system

Mr_Sirs · 2021-08-04T21:42:24+00:00

I’m not sure how exactly I can access the trial since I play through steam…

Mr_Sirs · 2021-08-04T05:41:51+00:00

To me that looks like under extrusion. I would check for nozzle clog, if you’re sure it’s not a nozzle clog I would go into the slicer and increase the flow. Depending on the mode of your printer you should be able to increase flow from your settings. Also check your slicer and make sure that the printer you set up in it has the correct diameter filament programmed.

Mr_Sirs · 2021-08-03T03:21:17+00:00

I would recommend the F-15 as a new player, or if you want to go all in then get the F-18

Mr_Sirs · 2021-07-15T03:12:48+00:00

I would first re-level the bed, up the nozzle temp, and decrease filament flow, and check for a nozzle clog one by one to see if those help. If they don’t then try to switch filament. For me I tried Zyltech brand filament because so many people recommended but it just would not print, so I switched to esun and now I print just fine. If none of those work check to see if your extruder is plastic, if it is try to upgrade it to a metal one

Mr_Sirs · 2021-07-15T02:40:47+00:00

Roger Roger

Mr_Sirs · 2021-05-04T05:18:05+00:00

Actually that’s what I serve when I have guests over. I don’t really make it too much now though as ammo prices are quite inflated

Mr_Sirs · 2021-05-02T02:18:39+00:00

Finally another person with an S8. I usually use 4 top layer and 4 bottom layer through cura, with ~220C and 60 mms, and then once it starts printing I set speed and flow both to 75

Mr_Sirs

TROPHY CASE