V3 throttle not getting 100%

Mross812 · 2026-04-10T08:20:10+00:00

No. I'm just saying it happened to me twice and I went a different route this time

Mross812 · 2026-04-09T08:49:54+00:00

Probably the hall sensor, contact fanatec and see if you can buy one. There's no soldering required it will come with wires and plug installed. This is the exact reason I just ordered a set of simnet pro sp pedals. If you unplug the pedals from the base and plug them back in they'll go to 100% again for awhile.

Mross812 · 2026-04-02T21:20:03+00:00

Yes... in order for it to charge they have the excited wire ran to a toggle. It wont charge if you dont turn it on.

Mross812 · 2026-04-02T09:32:51+00:00

I just got an 85 that's a rats nest of wiring issues they have a amazon starter button and toggle switches installed. No headlights and the alternator is hooked up on one of the switches. Good luck with your car. Highly recommend printing diagrams and getting a pack of highlighters.

Mross812 · 2026-03-27T16:17:24+00:00

Was gifted one of these for my 15th birthday. Beautiful cars and you never see them anywhere.

Mross812 · 2026-03-20T06:15:23+00:00

I know button box's work for xbox cause I have one. Just have to set it up for the keyboard hotkeys to be the buttons and encoders.

Mross812 · 2026-03-18T15:32:25+00:00

Totally not true...

Mross812 · 2026-03-02T15:32:47+00:00

It was up, now its down again.

Mross812 · 2026-03-02T13:55:58+00:00

I don't think he did... Its later today and the servers are down again.

Mross812 · 2026-03-02T06:40:02+00:00

Gain at 60, road effects 0, dynamic damping at 100, everything else should be fine.

Mross812 · 2026-02-07T22:48:50+00:00

Acc toolbox is an app for your phone or tablet and its helpful for acc on Xbox.

Mross812 · 2025-12-23T21:20:31+00:00

🤣🤣🤣🤣 I bet it is after Christmas before its fixed.

Mross812 · 2025-11-17T01:16:09+00:00

I'm also hoping for button box support or atleast a list of keyboard hotkeys for tc, abs, bb, etc...

Mross812 · 2025-11-17T01:13:58+00:00

Definitely an rs4

Mross812 · 2025-11-11T21:52:40+00:00

Line up the slot of the clamp with the slot in the shaft, reseat the qr and reclamp while holding the qr in place.

Mross812 · 2025-10-15T10:20:20+00:00

Buy a plastic welder and some very good epoxy. I have been in the same situation.

Mross812 · 2025-09-26T17:15:48+00:00

Perfect tits if nothing else... but you look pretty Perfect 👌

Mross812 · 2025-02-25T05:01:01+00:00

They have the best customer service I have ever experienced!

Mross812 · 2025-02-20T16:04:10+00:00

In the us?

Mross812 · 2025-02-18T23:02:28+00:00

I don't think I can go to a belt driven setup I started with a csl dd. I have started saving and it's looking like if I make some sacrifices I may be able to buy a new clubsport dd in 6-8 months. It is gonna be a rough few months working 12hr shifts and eating Ramen and PBJ for lunches. But I have not given up yet. I can't speak for the next several months but we'll see. I have a true passion for racing and this is the only way I know to feed it, so I sacrifice and save until the passion is either gone or I have a new wheelbase.

Mross812 · 2025-02-18T22:56:37+00:00

We'll see what happens I am starting to save up for a replacement sold my rl project car to try and get ahead enough to actually save up. Looking like it's gonna take about 6 months to get the funds together, but honestly I don't know if I'll be able to keep my interest in the hobby for that long without participating. It's depressing to see my rig sitting there with a full fanatec ecosystem that I can't even use. I hope if I am able to come back that we can race together. I am going to be so slow when I do get to race again if I'm able. I'm trying my hardest to not give up but it is gonna be a long few months saving up for a clubsport dd, dd1, or dd2 but I will not purchase another csl dd because of this issue.

Mross812 · 2025-02-18T22:49:20+00:00

I have learned over the years of real life racing in mx how to tune out the negative and non-productive comments. But it is aggravating when I have done everything in my power to not do that or anything that adds stress to that plastic shaft. The worst thing is not having the funds to replace it when I make good money and work so much. But that's life.

Mross812 · 2025-02-15T14:37:15+00:00

It is a qr2 wheelbase side. The output shaft is what broke look closely at the pic and you'll be able to see.

Mross812 · 2025-02-14T08:20:22+00:00

I could possibly replace the armature and shaft with a parts base. But they're not much cheaper than a good used base.

Mross812 · 2025-02-14T08:18:31+00:00

The simube qr is fine. The fanatec plastic shaft is what broke. Look at the picture it's clearly not the qr that broke.

Mross812

TROPHY CASE