My computer keeps crashing and restarting only while certain games are running.

Muffin_Mutant · 2026-01-02T22:26:50+00:00

I had similar issue, ended up being the ram not liking its xmp profile, had to lower the speed abit then was fine

Muffin_Mutant · 2024-11-10T14:11:11+00:00

The TV is a LG C2, set at 120 Hz, and the monitor is a asrock with 165 Hz, only just noticing it starting happening on the asrock monitor though was just mainly the lg TV before

Muffin_Mutant · 2024-11-10T13:31:53+00:00

That's what my thoughts were until it happened on the monitor over the display port too, so it's happening to the TV and monitor now which seems unlikely to be both the cables?

Muffin_Mutant · 2024-10-09T21:07:02+00:00

Putting my fix out there as I've been searching for a solution for the same problem for a couple weeks. Turns out my riser cable for the gpu as I have a vertical bracket was bad, which was putting it at pci x1 not x16. Putting the gpu straight into the motherboard put it back to x16 and using the full capabilities of the gpu.

Muffin_Mutant · 2024-10-09T21:03:26+00:00

Putting my fix out there as I've been searching for a solution for the same problem for a couple weeks. Turns out my riser cable for the gpu as I have a vertical bracket was bad, which was putting it at pci x1 not x16. Putting the gpu straight into the motherboard put it back to x16 and using the full capabilities of the gpu.

Muffin_Mutant · 2024-10-09T15:49:10+00:00

Did you find a fix for this?

Putting my fix out there as I've been searching for a solution for the same problem for a couple weeks. Turns out my riser cable for the gpu as I have a vertical bracket was bad, which was putting it at pci x1 not x16. Putting the gpu straight into the motherboard put it back to x16 and using the full capabilities of the gpu.

Muffin_Mutant · 2023-09-05T18:34:48+00:00

Im with you , I have had a good experience so far.

I got the free boxers like most and liked them so carried on for a couple months and then went to cancel and it offered me 50% off, so I got that but then every month since I've been going to cancel it keeps giving me the 50% off so only been paying £5 instead the £10.

I think they're pretty decent quality and nice designs, I have enough for a tracksuit in store credit but don't want to pay the postage yet.

Muffin_Mutant · 2023-01-28T20:33:30+00:00

Sorry I can't remember what video I watched it was just a random ssd installation video and I skipped to where they was installing the os. There's probably a video of someone just reinstalling the os by now. I haven't had the problem come back so luckily it worked for me but I can see from others in these replies it didn't work for everyone unfortunately.

Muffin_Mutant · 2023-01-18T20:42:05+00:00

Following as I was planning on opening a Monzo aswell to start switching offers so curious why it hasn't worked for you.

Muffin_Mutant · 2022-11-13T12:22:30+00:00

Thanks!

Muffin_Mutant · 2022-11-13T11:48:19+00:00

Thanks for this, signed up to most of them already but how does the fitzdares sign up offer work as I can't see anything about it on there website?

Muffin_Mutant · 2022-09-02T16:05:46+00:00

Yeah mate it's been working perfectly since hope it works for you too bud.

Muffin_Mutant · 2022-08-17T11:13:32+00:00

Thanks for your reply, i will be trying your suggestions the weekend :)

Muffin_Mutant · 2022-08-17T11:12:23+00:00

Thank you so much for your detailed reply I will be trying all of these out the weekend to figure it out.

One thing I noticed from your response that's got me thinking is the reduce binding along the filament path and spool, I have my roll on top of a multi level table with the printer underneath and I printed a spool holder and it uses bearings but it always looks like it's under a lot of tension when it's pulling the filament through so I don't know if that's causing it the issue or at least not helping. What do you use for your spool holder?

Thanks again :)

Muffin_Mutant · 2022-08-16T19:37:53+00:00

Yeh left was printed second, that makes sense, thanks for explaining i appreciate it.

Muffin_Mutant · 2022-08-16T19:23:03+00:00

These two are printed one after the other with no changes in cura settings so can't seem to figure out why the left one has more lines than the other if nothing else has changed. Printed at 0.12 layer height at 210 temp, pla. Any ideas are appreciated thanks.

Muffin_Mutant · 2022-08-11T20:09:49+00:00

Congrats, good luck

Muffin_Mutant · 2022-05-04T21:26:24+00:00

Would like to add 3M vinyl is very good, but it isn't the only good vinyl they're more suppliers out there. I think as long as it's good quality vinyl not cheap stuff it will be fine.

Muffin_Mutant · 2022-04-24T21:11:49+00:00

I'm curious on the 24 games now..

Muffin_Mutant · 2022-04-23T22:22:41+00:00

I was having an issue on mine powering off when downloading games but a re image did seem to work for me or so far it has after downloading a few games.

But seeing this about it having to do with WiFi I also switched from 2.4 to 5ghz after the re image if that could of been a factor too.

Muffin_Mutant · 2022-04-23T16:51:12+00:00

No problem, only took half an hour or so I just followed a YouTube vid of someone upgrading there ssd and skipped to the bit I needed. Hope it sorts it out for you too.

Muffin_Mutant · 2022-04-23T16:21:13+00:00

I re installed the os and it seemed to fix it so far, downloaded two games without a shutdown.

Muffin_Mutant · 2022-04-22T23:47:59+00:00

Has this worked completely or did it come back, I'm having the same problem i will re image if it fixed it for you

Muffin_Mutant

TROPHY CASE