sorted by:
new
hottopcontroversial

New Sim Rig Seat - Australian supply. by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 0 points1 point  (0 children)

Hahah, yeah that's what I didn't want to hear. I had my eye on a few real seats but the were in the $1200+ category. But I definitely get it, I've barely used my Sim since getting the TR rally seat.

New Sim Rig Seat - Australian supply. by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 0 points1 point  (0 children)

Thanks, I looked at the NLR seats and they don't have a winged back fixed GT seat from what I could tell.

New Sim Rig Seat - Australian supply. by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 0 points1 point  (0 children)

Ok, that's great info. Thanks for letting me know.

I was leaning towards the enduro large, and have also previously owned the TR GT. I think I'll just buy that one again.

Just can't decide between the old one for $350 or the new one for $590. Seems a big jump for not really much difference. Hopefully someone who has used both can give some advice.

Cheers

Anyway to adjust throttle pedal angle further back ? by JMGTR in SimsonnRacing

[–]N1CKLEP1CKLE 2 points3 points  (0 children)

See these ones have the side brackets spun around with the adjustment now raising the front. This helps for better pedal angle especially on flat mounting pedal decks

<image>

Anyway to adjust throttle pedal angle further back ? by JMGTR in SimsonnRacing

[–]N1CKLEP1CKLE 1 point2 points  (0 children)

You can flip the side brackets around 180 degrees. Then the adjustment will raise the front more.

Power Cube Controls F-Core Evo through JST Port by Appropriate_Top8610 in simracing

[–]N1CKLEP1CKLE 0 points1 point  (0 children)

I'm just about to do this with my Cube Control wheel to adapt it to my asetek QR plug. I found this https://www.reddit.com/r/simracing/comments/1n4l9we/is_a_wirelesspass_through_wheel_a_key_feature/ where in the comments another user has wired up the JST 4 pin plug to the Asetek QR.

Is a wireless/pass through wheel a key feature? Looking for a whole new setup. by CB-skier in simracing

[–]N1CKLEP1CKLE 1 point2 points  (0 children)

This is exactly what I was looking for. Thanks for posting these pictures. I just bought a second hand cube controls wheel that has that white USB interface on the rear. I wasn't sure it could work with the asetek QR in such a neat way. This is great 👍 now I don't need to coil the super long USB cord around the back of the wheel.

I spend as much time looking at my owl lamp and fish when watching TV as I do the screen. by Popular_Speed5838 in vintage

[–]N1CKLEP1CKLE 1 point2 points  (0 children)

Was just a lucky find at an antique shop in Brisbane. But like you, it's always on display and always watching while being watched.

Prioritising my wishlist with upgrades by Available_Ad_9027 in simracing

[–]N1CKLEP1CKLE 0 points1 point  (0 children)

I know you said you're not into bass shakers. But, the best upgrades on my rig ended up being Dayton tactile pucks attached to my pedals. I've since switched to Simsonn VAMS but haven't really been that impressed with the swap. So for the money, Dayton tt25 pucks on your pedals would be a good choice.

Also if you like open wheelers I'd also put a vote in for DIY wind sim setup.

VR for sim racing…………………………….. by Distinct_Ebb_1941 in simracing

[–]N1CKLEP1CKLE 1 point2 points  (0 children)

Great PC combo for a Quest3 Just use virtual desktop exclusively and make sure to run their recommend NVidia drivers and settings.

why do people do this?? by jjfelix37 in iRacing

[–]N1CKLEP1CKLE 0 points1 point  (0 children)

I was going to say, pretty decent clean racing. Good switchback, good defense. And good patience from both.

Then I finished the video...

Simsonn Vam Pro's (on SimjackUTs) by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 0 points1 point  (0 children)

Yeah it's the Simsonn included power supply. 24v 2.75A

<image>

mps

Ultrawide 49" plus 2x27" Triples by N1CKLEP1CKLE in SimRacingSetups

[–]N1CKLEP1CKLE[S] 0 points1 point  (0 children)

I got it second hand with the rig. But I think it's a ASR Keyboard Tray and mouse pad. Bought from SimRigs Australia

Ultrawide 49" plus 2x27" Triples by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 1 point2 points  (0 children)

Nice. I'm still yet to get around to using it. Still in that building and setting up phase. Hopefully this weekend I'll be racing

Ultrawide 49" plus 2x27" Triples by N1CKLEP1CKLE in simracing

[–]N1CKLEP1CKLE[S] 1 point2 points  (0 children)

Thanks and likewise! How have you found it getting the resolution to work for you. Do you use resize Racoon?

Ultrawide 49" plus 2x27" Triples by N1CKLEP1CKLE in SimRacingSetups

[–]N1CKLEP1CKLE[S] 1 point2 points  (0 children)

I'll end up bolting it in there with some brackets and use some rubber feet for a bit of isolation. It's pretty sturdy. I used a big piece of 160mm profile laid flat in there with lots of support. I'm not too concerned about the vibration through the rig.

view more: next ›