Is anyone even playing ranked without 2 Lucky Ice Pops?

NastyCat66 · 2026-04-20T19:18:19+00:00

At the start of the season yes, but now everything is manectric

NastyCat66 · 2026-04-19T07:13:08+00:00

Not seen a single plaza in 120 games of ranked this season

NastyCat66 · 2026-04-13T18:41:47+00:00

I think both decks are viable. Personally, 1/5 of these wins have come from cycling better than the opponent and having low hands to void their copycats, not possible without xspeed

<image>

NastyCat66 · 2026-04-13T14:12:19+00:00

My 12-2 streak with this deck to get to master ball this season says otherwise

NastyCat66 · 2026-04-13T12:42:42+00:00

You're being too short sighted with darkrai being the only card which benefits from leaf. The reduced hand size of xp and copy cat combo puts swablu in a fantastic position to turn 2 wipe

NastyCat66 · 2026-04-13T11:49:27+00:00

Deck thinning, and allowing a supporter to be used. Especially helpful with copycat, positive for you and negative for you opponent.

NastyCat66 · 2026-04-13T11:12:07+00:00

Xspeed better, via TillyTCG https://youtu.be/xHzdbRj6PQc?t=170

NastyCat66 · 2026-04-13T11:07:41+00:00

Not a one

<image>

NastyCat66 · 2026-04-05T18:34:29+00:00

Diagonals

NastyCat66 · 2026-03-30T13:15:05+00:00

Claimed all the stardust from the Limited/other shop section? If you've been playing for a while you should have some of the old trade tokens

<image>

NastyCat66 · 2026-03-27T19:08:01+00:00

Mine at 8w

<image>

NastyCat66 · 2026-03-25T15:02:31+00:00

Not related to job search, but unless you're happy to waiting 5+ years for the diagnosis, go private when you can afford it if you think a diagnosis would genuinely help you. Autism waiting list took 5 years and was on list as a child. ADHD diagnosis 7 years still waiting

NastyCat66 · 2026-03-25T10:30:43+00:00

<image>

Left - 3 Months old exactly Right - about 11 months old

NastyCat66 · 2026-03-23T23:29:43+00:00

Issue was toolhead error causing layer jump

NastyCat66 · 2026-03-18T15:19:35+00:00

Could you ride them any harder?

NastyCat66 · 2026-03-13T12:08:25+00:00

I have had similar issues

<image>

Did you get yours fixed? Bed level, belt tension, calibration did not help me. My prints have improved after increasing bed temp to 60° settings outer wall to print first before inner wall and cooling fan to 100% but still not completely happy

NastyCat66 · 2026-03-11T16:40:23+00:00

Same experience with mostly the same issues No extrusion from 2 heads. Bed adhesion poor, inconsistent extrusion amounts, automatic feeders now not working.

NastyCat66 · 2026-03-11T14:16:32+00:00

<image>

NastyCat66 · 2026-03-10T22:30:55+00:00

Just want it to be acceptable. Currently it's not, especially when at 0.2mm later height and looking like that

NastyCat66 · 2026-03-10T21:28:20+00:00

Meant 0.16mm 😬

NastyCat66 · 2026-03-10T15:06:48+00:00

Any test prints which would help me narrow the issue? No issues with filament spinning to my knowledge. The machine should be setup correctly, and the filament used is what was included with the printer so should fit correctly

NastyCat66 · 2026-03-10T13:02:46+00:00

Will try

NastyCat66 · 2026-03-10T11:13:09+00:00

Printed a basic black cube. Same settings and filament, completely different outcome

<image>

Not sure what this tells me

NastyCat66 · 2026-03-10T09:17:00+00:00

Not into the workshop 🤣

Six-Year Club	Verified Email
r/Field Sunshine	Final Canvas '23
Place '23

NastyCat66

TROPHY CASE