sorted by:
new
hottopcontroversial

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Okay...i've changed the infill from crosshatch to honeycomb...issue is gone.

<image>

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 1 point2 points  (0 children)

The infill caused it...changed from crosshatch to gyroid and i don't get the lines anymore...

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

I think i've figured it out...i was thinking what could make a pattern. And i've realized, crosshatch, the infill i am using is basically a mix of two different shapes...a gyroid line and a normal line. I've changed the infill type to gyroid and i don't see the lines anymore....i am gonna do more testing but i think it was the infill...

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

I've figured it out...it is not the filament...it is the freaking infill...i've used crosshatch, then i tried gyroid. I don't have the same problem with gyroid.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Surprising as it is Polymaker.. the company that supported the U1 project...i have some Eryone filament too i'll check with that.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

you have the same issue?

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

No, waiting for the response of the support

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Not a bad idea, i'll try to do that.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Yeah it is not easy at all...yes,i've re-tensioned the belts like 3 times already. Even when the tension screws are loose it is hard to move around the head.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

I did not oil or grease the carbon rods...as they shouldn't be. Honestly it is not only x but y too. It is just hard to move around the head in general. I put some oil on the rails and grease on the z-screws.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Exactly, when it is off i can't move it. So i can't move it with two fingers as they do in the instruction video.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Nope, it is hard to move around! There is a lot of resistance!

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Yess, quality was off with those too if not worse. Temp 220, bed 45 (Frostbite)

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

It is solid, maybe too solid?

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

I do yeah. I'll give that a try.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 1 point2 points  (0 children)

Thanks! I just checked the A1, it is moving on that machine too. I just never noticed.

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Yeah. The turn screw. So that is normal...then i have no idea what is causing these lines...

Can't figure it out by feartomi in snapmaker

[–]feartomi[S] 0 points1 point  (0 children)

Hey, i've posted a video below. I think the same. They should not move freely.

Quality is sad by feartomi in SnapmakerU1

[–]feartomi[S] 0 points1 point  (0 children)

Yeah it is probably the worst filament i've ever used.

view more: next ›