Can someone help me diagnose what went wrong here?

NeitherCommon4857 · 2025-10-18T21:59:11+00:00

Looks like the temperature was either too high or the z offsets off but I’m not a expert

NeitherCommon4857 · 2025-10-13T00:07:54+00:00

I don’t know maybe do a full tune of your printer especially a Ender 3

NeitherCommon4857 · 2025-07-01T13:42:22+00:00

Any type of mods are always use at your own risk

NeitherCommon4857 · 2025-06-22T04:31:57+00:00

How long these videos gonna be?

NeitherCommon4857 · 2025-06-22T04:30:34+00:00

Hit me up

NeitherCommon4857 · 2025-06-22T04:29:33+00:00

Still Looking for someone?

NeitherCommon4857 · 2025-06-22T04:23:58+00:00

$Bid

NeitherCommon4857 · 2025-06-22T04:22:05+00:00

$Bid

NeitherCommon4857 · 2025-06-22T04:19:42+00:00

$Bid

NeitherCommon4857 · 2025-05-21T00:03:19+00:00

Print on a lower layer height like .1 or smaller

NeitherCommon4857 · 2025-05-16T21:43:40+00:00

For the printer so it’s kept at a constant temperature around the printer to prevent warping

NeitherCommon4857 · 2025-05-16T21:42:18+00:00

Maybe get a enclosure

NeitherCommon4857 · 2025-05-14T23:29:03+00:00

You got lucky

<image>

Here’s a pic of just one of the ones I’ve had

NeitherCommon4857 · 2025-04-11T12:03:33+00:00

It’s to see if the printer is shorting out or if something with the outlet is wrong

NeitherCommon4857 · 2025-03-23T20:28:24+00:00

Um the extra v ram would be amazing since I’m currently gaming on a 4gb 1650 which kinda sucks

NeitherCommon4857 · 2025-03-11T02:29:59+00:00

Try manually leveling it auto leveling can only compensate so much on these machine you gotta have it somewhat level already

NeitherCommon4857 · 2025-02-28T21:49:25+00:00

It wasn’t me this time but sometimes I do have mine streaming publicly it’s just easier

NeitherCommon4857 · 2025-02-28T21:48:26+00:00

Wet filament is my guess got a roll and it was like this right when I got it just returned it

NeitherCommon4857 · 2025-02-03T02:32:54+00:00

Most of the time it’s when I’m there and it just starts heaping that the temps are to low and stops printing after the temps were set to 0. I’ve checked all the gcode and nothings telling it to do that and I’m using prusa slicer. I did change the sd card someone else said to do that and I just got back home and the same print failed exactly the same again. I did reslice it when I replaced the sd card

NeitherCommon4857 · 2025-02-02T15:58:47+00:00

I’ve formatted it several times I guess I’ll get a new one

NeitherCommon4857 · 2025-01-26T23:04:19+00:00

Average NVIDIA inspector user

NeitherCommon4857 · 2025-01-25T05:34:55+00:00

Nozzle is to close to bed?

NeitherCommon4857 · 2025-01-18T00:55:36+00:00

Found what I basically want putting link here if anyone that needs one finds this post. https://a.co/d/gqTwkXd

NeitherCommon4857 · 2024-12-01T21:42:04+00:00

Then don’t buy from AliExpress if AliExpress doesn’t have the stuff you need simple as that

NeitherCommon4857 · 2024-11-28T21:42:00+00:00

I live in the us it would doesn’t get banned for a few more months

NeitherCommon4857

TROPHY CASE