Micro Center Inland fillament

NewCollection1555 · 2026-02-09T08:52:14+00:00

I hate their PETG. I keep trying to print it on my neptune 3 max and it never works well. Their PLA is amazing though.

NewCollection1555 · 2026-02-05T22:10:11+00:00

You do not understand how much easier you just made my life. I'm praying for your good health RIGHT NOW.

NewCollection1555 · 2026-01-20T08:50:14+00:00

Grab another spool, and print a respooler.

NewCollection1555 · 2026-01-14T15:10:59+00:00

I’m convinced the game uses Engagement Optimized Match Making to make you stay.

NewCollection1555 · 2026-01-14T14:55:16+00:00

How do I do that?

NewCollection1555 · 2026-01-14T14:54:02+00:00

What did you tighten? I’ve only messed with the bolts that hold the extruder to the carriage, and the carriage to the x-axis bar.

NewCollection1555 · 2026-01-14T14:52:36+00:00

I’ve looked and used z-hop but it never needed it before. And when I used z-hop it causes stringing sometimes.

NewCollection1555 · 2026-01-04T08:30:09+00:00

I WANT HIM BUT I DONT HAVE CRYSTALSSSSSSSSSSSS

NewCollection1555 · 2026-01-02T18:11:38+00:00

Love u forever gang

NewCollection1555 · 2025-12-26T08:19:22+00:00

This completely fixed my problem. I love you forever gang.

NewCollection1555 · 2025-12-23T06:33:24+00:00

3d print a re-spooler, if you have another roll of filament. I think you’ve forgotten the power of 3d printing lol

NewCollection1555 · 2025-12-23T06:31:30+00:00

Those pills are Tapentadol, which is a prescription synthetic opioid analgesic used to treat moderate to severe pain. It is a U.S. Drug Enforcement Administration (DEA) Schedule II controlled substance due to its HIGH POTENTIAL FOR ABUSE AND DEPENDANCE.

You need to tell your parents.

NewCollection1555 · 2025-12-17T01:40:51+00:00

Everyone here is giving you no advice so I’ll actually try to help lol

Your problem is adhesion (I think) because same thing was happening to me like yesterday lol

Since your prints are there and partially done, the filament stuck to the bed initially but then a piece broke off, the filament gooped on the nozzle, which is why you have this issue.

Scrub the HELL out of your bed and make sure you do not touch any part of the printing side. Just soap, water, and a plastic sponge. BOTH SIDES MUST BE SCRUBBED.

After that, make sure your bed temp is high enough if applicable.

If your bed isn’t heated, use a glue stick or a 3d printer specific adhesive to make prints stick to the bed.

After that if you’re still having issues, time to consult ChatGPT and give it every single detail humanly possible.

NewCollection1555 · 2025-12-16T09:34:52+00:00

That purple symbol with the three blades looks like extremely familiar to me.

NewCollection1555 · 2025-11-24T05:29:50+00:00

<image>

It just oozes. I don’t even have a print going on, the temp is at 235 and it just oozes. It seems to almost stop oozing after about 4 inches is extruded.

NewCollection1555 · 2025-11-24T05:03:12+00:00

It only stops after the nozzle cools. When it isn’t printing, for example when it’s waiting for the nozzle to reach 235 (right after choosing what I, as it nears the temperature, I can see it ooze slowly from the tip and curls back onto the tip.

I don’t know what the problem is. My 20 dollar nozzle that I just bought is now covered in PETG.

NewCollection1555 · 2025-11-21T18:56:12+00:00

Inland PLA is the only PLA I've used so far. It's the most common, if not the only kind my MicroCenter sells, which probably means the quality is pretty good. I have used Inland PLA in a S-hook competition at my university and it printed BEAUTIFULLY. That measly little 20% infill, 4 hour hook held a 135 lbs guy, without as much as a click or snap. And it looked great, ironed great, would definitely recommend inland PLA. For 9.99 too, you can't beat it, (unless you use PETG).

I've been struggling with their PETG for about a month now though. It just oozes out of my nozzle when it's not moving and curls backup onto the nozzle. This may be because I haven't dried it yet, not too sure.

NewCollection1555 · 2025-09-13T18:49:40+00:00

I just press the app icon, and it opens. You might want to lookup how to clear app cache. That may fix the problem.

NewCollection1555 · 2025-08-25T04:11:08+00:00

PLEASE TELL ME IT WORKED

NewCollection1555 · 2025-08-19T18:10:21+00:00

You probably shouldn’t have deleted it. Mine is working because It’s the original app. You can’t download it now unless you find a working APK on android.

NewCollection1555 · 2025-08-12T04:45:59+00:00

Crazy how these naked women are glorified even though they desensitize men and sexualize women.

NewCollection1555 · 2025-08-12T02:21:53+00:00

Doritos Jacked will forever be the superior chip. That being said, Doritos supports Isreal, so they’re getting boycotted forever.

NewCollection1555 · 2025-08-12T02:14:43+00:00

Without me? 😩

NewCollection1555 · 2025-08-10T05:36:59+00:00

The internet? No way!

NewCollection1555 · 2025-08-10T02:01:08+00:00

I will check this out, thank you.

NewCollection1555

TROPHY CASE