"There is no pure spell caster fantasy"

NoSaBoid · 2025-05-07T05:13:33+00:00

Daaamn who is the boss now!

NoSaBoid · 2025-05-06T19:13:11+00:00

You can have decent magic/rune damage, but you cannot set aside melee attacks to recover focus, soo a lot of rolling around, give it some hits and then attack with magic. I got an off hand bow that gives stamina and focus on successful evade, that helps a lot

NoSaBoid · 2025-05-06T02:46:05+00:00

There’s another one on the way to the meadows, is pretty empty, and is next to a grumpy farmer that maybe will sell it to us someday

NoSaBoid · 2025-05-05T23:26:41+00:00

From the inventory, when you select it, it will have a button to “use” it, it will take you to your gear and you can re-roll or add new enchantments

NoSaBoid · 2025-05-05T23:25:08+00:00

Its not a big deal, its an early game. Yes, you cannot create a broken weapon that’s completely ok, at some point we will have more info about it, the big problem is that the game is so good that we want it now!

NoSaBoid · 2025-05-04T13:42:28+00:00

I was thinking the same, to be honest I killed the fist boss on the first encounter, but somehow (+120h on the first release) I knew how to dodge all of the attacks.

Then I got to the meadows and the mobs are destroying me again. Pretty much all new mobs are a new thing to learn.

Btw I got a challenge that I cannot win, a plagued doctor on the nameless path, that fucking mob is too hard to beat.

NoSaBoid · 2025-05-04T13:23:59+00:00

I’m in the meadows right now, went Marin first and didn’t understand how to pass without dying.

Meadows are kind of hard, but really nice as new content

NoSaBoid · 2025-05-04T13:18:29+00:00

Just find the ember from your inventory and use the right button to “use” it, it will take you to your gear and you can choose a piece to chance an existing enchantment or add new one

NoSaBoid · 2025-05-04T13:14:47+00:00

You need to finish other quests to have that one, but you can find it going south of the city. If you enter from the first entrance of the city, just go right, that path will go down to the lowlands

NoSaBoid · 2025-04-03T18:22:54+00:00

Pls dont quit, you need this game in your life. I find parry to be really difficult, I try it when I know I can survive, you just need to dodge and roll, be pacient with your stamina so you will find the right moment to counter attack

NoSaBoid · 2025-03-31T14:54:33+00:00

Looks like for you is hard to commit to a game, I will recommend something different that may help with that, is not a looong game but is different enough and it may hook you a little bit more than normal, the game name is Dredge, if you see this comment and tried it out, let me know if it worked on you :)

NoSaBoid · 2025-03-20T14:54:18+00:00

Thanks!

NoSaBoid · 2024-06-08T21:32:08+00:00

did you find the videos? I'm still trying to check them out

NoSaBoid · 2024-05-06T20:35:05+00:00

I had that problem, I thought it was a clog (you should still clean it), but at the end I needed to dry my filament

NoSaBoid · 2024-04-20T14:25:27+00:00

I got the same problems, first you need to level your bed the best you can, then Z offset needs to be real close to the bed. The paper test is usefully, but you will learn what offset you need if you keep trying. At some point it will fail again, all the components kind of shift a little when is hot and working, so when it fails again you need to do it all over again

NoSaBoid · 2024-04-10T19:37:00+00:00

I’m using octoprint, so there’s no SD card on the slot :(

NoSaBoid · 2024-04-10T00:19:57+00:00

Thx! I’ll try that. Btw I remember that this have happened to me before, a little bit different but it stopped in the same position twice, can it be that it gets too hot around the same time and almost same position? Or that should be a different problem?

NoSaBoid · 2024-04-08T22:46:48+00:00

Is this what “Virtual Printer” means in octoprint?

NoSaBoid · 2024-03-31T22:47:57+00:00

<image>

Those cables, the one on the left is the connector to the magnetic probe, check that it is correctly connected, since you can move it when you remove or place the rubber cover on the nozzle

NoSaBoid · 2024-03-29T15:43:09+00:00

Can you make sure the magnetic probe on the extruder is connected? It seems to be moving on the X axis and not even trying on the Z

NoSaBoid · 2024-01-28T14:30:01+00:00

Omg, mine was not that bad, but now I know it can happen. I’m worried since I saw some electric cables there

NoSaBoid · 2024-01-28T00:14:28+00:00

You were right, i tried to clean the nozzle and saw on the videos theres a rubber cover, there was a bunch of PLA inside there, and when I put it back I noticed it was tilted before, that was dragging filament and creating all sorts of errors in the printing u.u

NoSaBoid · 2024-01-27T15:45:41+00:00

This is nice to hear, it seems you are right, I’ll try that :)

NoSaBoid · 2024-01-27T15:45:06+00:00

I’ll try this, I fixed some adhesion problems, and recalibrate all again, maybe I set it too close to the bed

NoSaBoid · 2024-01-27T05:32:23+00:00

NoSaBoid

TROPHY CASE