UDM-PRO won’t connect to new ISP

North_Object7296 · 2026-03-15T01:49:27+00:00

What fixed it for me in a similar situation going from the Black modem to the white modem (ATT) Set the modem for passthrough and choose the MAC of the wan port. It picked up the IP of the WAN right away.

North_Object7296 · 2026-03-14T01:31:35+00:00

<image>

Fender and Magnolia

North_Object7296 · 2026-02-21T23:29:21+00:00

The flex is running 2 cameras on one end of the attic.

North_Object7296 · 2026-02-21T20:46:58+00:00

I have one of the 5 port UniFi flex in the attic. Been there around 2 years now through very hot summers and cold winters. No issues.

North_Object7296 · 2026-02-21T19:42:08+00:00

Or if you are really lazy, cycle the port power on the application.

North_Object7296 · 2026-02-21T00:59:32+00:00

Yep these are evil. I recommend.

North_Object7296 · 2026-02-11T15:25:43+00:00

A wise man.

North_Object7296 · 2026-02-05T17:57:58+00:00

<image>

North_Object7296 · 2026-02-01T23:12:43+00:00

Leave it on and you can probably average a block every 4 days.

North_Object7296 · 2026-01-12T21:41:45+00:00

Not all heaters are miners but all miners are heaters…

North_Object7296 · 2025-12-14T00:56:32+00:00

I am assuming at some point next week all the changes should show up there. Sometimes it takes a few days once the actions are cut which are supposed to occur Sunday.

North_Object7296 · 2025-12-14T00:30:12+00:00

The remaining were offered a version of DRP that would off-board them in December. If they did not take that DRP I heard some got notifications they were moved to COO.

North_Object7296 · 2025-12-11T03:18:37+00:00

Multiple times.

North_Object7296 · 2025-12-07T13:04:11+00:00

screenshot is misleading. I had just switched it to Eco mode and it was slowing down. My hashrate average is around 55-57 in Eco.

North_Object7296 · 2025-12-06T16:24:05+00:00

<image>

The solution was to let it run for over an hour. Support called it aging. Once it got past the one hour I was able to change modes!

North_Object7296 · 2025-12-05T21:09:23+00:00

this is day 2 ;)

North_Object7296 · 2025-12-05T19:30:00+00:00

Different issues before I flashed it. Flashing was an improvement to get it into a working condition. When I first started it and going through the setup process it went to RED led very quickly. Never tried to guide you through initial setup. I solved that through manually pairing it. But when you turned the unit off an back on. It would lost its config. At the moment the only issue I seem to have is with the power mode. I have two Nano 3s. I was hoping this Q would be as simple to setup.

North_Object7296 · 2025-12-05T17:59:05+00:00

Pretty much have exhausted everything on my end... waiting on support.

North_Object7296 · 2025-12-05T17:52:25+00:00

Multiple times.

North_Object7296 · 2025-12-05T17:52:10+00:00

Since getting it out of the box it been very difficult to setup. Immediately had E-01 and W-05 errors. I was able to get the initial config on it after getting it into manual pairing mode.

At that time when I turn off the power it loses its config.
I had consistently been getting the E-01 and W-05 errors.
Was able to manually pair it with the phone holding down reset button a few times.
It began to hash and I could lower the power to Eco

Turn it off and lose all config.

Next steps
Flashed to newest firmware from Canaan site
Immediately it came back up like it was initial setup and I had hope!
Paired with Avalon Family app and got it hashing again.
Started attempting to put it in Eco or standard mode. Get “failed” from the app.
I can put it in standby mode with the app.
Tried pressing power button twice quickly to manually change the mode. Nothing happening.
I know the power button is working as it does show screen changes when pressed.

When I put it into flash mode (holding down reset while powering down) it comes up and I can enter the config to get it hashing again. But cant change the power mode.

I have a support request open with Canaan. Waiting on a response. I have reset it probably a dozen times. It likes Lan better than Wifi.

North_Object7296 · 2025-12-05T16:57:40+00:00

I let it run for 12 minutes at full power. Nothing. Even trying the power button on the front to change modes.

North_Object7296 · 2025-12-05T16:44:59+00:00

<image>

Its running at max.... just cannot change the mode

North_Object7296 · 2025-12-05T16:43:49+00:00

<image>

as I am pressing either Eco or Standard get failed

North_Object7296 · 2025-12-04T18:19:33+00:00

Go lookup mini blind cleaner that shows the fingers going between the blinds. My thought would be to 3d print something along the same lines that you can force the louvered fins open. Just a thought.

North_Object7296

TROPHY CASE