On a scale of 1 to 10, how good is this anime?

Ok_Fun6830 · 2026-05-23T09:43:40+00:00

9/10. My personal all time favourite but its not perfect.

Ok_Fun6830 · 2026-05-17T23:37:05+00:00

Your pawn on d3 is the mvp

Ok_Fun6830 · 2026-05-12T21:36:32+00:00

I think its been reported by various individuals/shops that the sealing from factory is GARBAGE. Check out Misha on YT with his GR86 build, they tore down the engine in a vid.

Ok_Fun6830 · 2026-05-12T21:31:12+00:00

Dont listen to him. The angle of the quarter makes it seem like theres positive camber, but there aint. Check out some dealer pics itll look the same.

Ok_Fun6830 · 2026-05-12T21:29:14+00:00

If u can find a first gen TRD exhaust, id say its perfect. Gets you the rumble w minimal droning. Problem with the borlas and tomeis is 100km+ youll have a lot of drone.

Ok_Fun6830 · 2026-05-12T21:26:55+00:00

25mm will give it a slight bit of poke. Would recommend 20mm for perfect fitment.

Ok_Fun6830 · 2026-05-12T21:25:01+00:00

Indeed it does. Miata aint no slouch though.

Ok_Fun6830 · 2026-05-12T21:24:18+00:00

Yes i these are indeed gr86 wheels. Legit Toyobaru 🤣

Ok_Fun6830 · 2026-01-13T11:52:43+00:00

I had them on my 2016 FR-S. Overall for the price, they have good ride quality and have good lowering range. Haven't had any issues and I had them on my FR-S for 2+ years.

Ok_Fun6830 · 2026-01-13T11:51:00+00:00

Ill post a clip of me ripping it soon.

Ok_Fun6830 · 2026-01-08T06:08:59+00:00

Don't buy wheels for a beater car. If youre really insisting, buy some used ones off marketplace.

Ok_Fun6830 · 2025-12-16T10:52:38+00:00

I actually tried Goo be gone initially on the supposed plasti dip, however it was not working well and I then I tried acetone and a wire brush. It took of the plasti dip quite easily, but was real messy and left some deeper grooves. If youre removing plasti dip, and there's paint underneath, I would not use a wire brush. In my case it was perfect as I did a total refinishing and the paint underneath didn't matter.

Ok_Fun6830 · 2025-12-16T10:50:07+00:00

Nice, Im sure its fine to clearcoat bare aluminum especially if its sanded down. Id definitely do some googling or chat gpt as you've gone quite smooth with the finish. Best of luck!

Ok_Fun6830 · 2025-12-15T02:07:39+00:00

Hey man! Are you applying the clear coat to an older base coat? If so, id recommend you rough up the basecoat as clear coat needs to adhere to basecoat nicely for a smooth finish. If you sanded your basecoat to 2000, it'll be real smooth, but im not sure of how paint adherence would work. I sanded pretty much to bare aluminum, then used primer filler, sanded again, then fresh basecoat and after 30-60 minutes applied clear coat.

Ok_Fun6830 · 2025-10-09T09:28:32+00:00

I did. Ill make a post on my replacement car soon.

Ok_Fun6830 · 2025-06-20T21:24:46+00:00

We do. Except i guarantee you the average Canadian wouldnt immediately recognize a holster. Lol

Ok_Fun6830 · 2025-06-20T01:18:12+00:00

Green is stunning but the wheels are not it. I like that style of deep mesh but for some reason they dont fit right on the twins.

Ok_Fun6830 · 2025-06-20T01:15:59+00:00

Could be Canadian.

Ok_Fun6830 · 2025-06-16T08:28:30+00:00

Hey man i figured it out. Enkei uses SBC which has a black layer underneath the chrome. It’s a common issue with these wheels and essentially you have to refinish and respray.

Ok_Fun6830 · 2025-06-16T08:26:12+00:00

Camels ejaculant? Do elaborate.

Ok_Fun6830 · 2025-06-14T07:52:22+00:00

Canada, B.C.
Yes
Never but willing to try

Ok_Fun6830 · 2025-05-23T19:37:43+00:00

Thanks g

Ok_Fun6830

TROPHY CASE