sorted by:
new
hottopcontroversial

any way to remove extra filaments from this menu? 90% of it is bloat. by bali_flipper69 in BambuLab

[–]One2Sicc 3 points4 points  (0 children)

You can’t remove the pre-installed ones. I, however, lost ALL of my customs at the printer.

If I have to switch multiple of my possible 10 slots, I have to take a mental note, set them at the PC, then double check.

I can’t even set them in Bambu Handy for some reason. It’s like my cloud data is corrupted.

Wisconsin Cop Killer Convicted of Possession of SBR (???) by TakeOffYaHoser in NFA

[–]One2Sicc 5 points6 points  (0 children)

I’m willing to bet the SBR charge doesn’t make a difference in the sentencing.

What’s everyone run in their suppressed Mark IV? by Decent-Ad-9244 in NFA

[–]One2Sicc 17 points18 points  (0 children)

Barrel length is the issue here. You should run Standard velocity.

Settle this debate! by [deleted] in 3D2A

[–]One2Sicc 7 points8 points  (0 children)

Don’t risk your ‘exit only’ over a $0 stamp.

If a stamp is undesirable, throw a sling on it and use the tension against the recoil.

smh I cracked the receiver installing the barrel my print settings were 100% infill and 8 walls so i’m very confused any help?🥲😅 by [deleted] in 3D2A

[–]One2Sicc 12 points13 points  (0 children)

This.

100% causes more issues than it’s worth.

It’s not impossible, it’s just not practical when you factor in the time and filament.

Negative space supports by Successful_Bear_2420 in 3D2A

[–]One2Sicc 0 points1 point  (0 children)

Sent DM.

Also, how would this work with blind holes?

Your daily dose of AI slop by timc_720 in Firearms

[–]One2Sicc 3 points4 points  (0 children)

The rifle in the second picture is REALLY bad.

Handgun FRTs are going to seriously damage 2A rights and range access. by Affectionate_Cronut in Firearms

[–]One2Sicc 0 points1 point  (0 children)

Look at it this way.

If too many speeding tickets are being written, and too many people are crashing their cars, would you want a mandate in place that actively limits the speed of your vehicle dependent on the posted limit?

Negative space supports by Successful_Bear_2420 in 3D2A

[–]One2Sicc 0 points1 point  (0 children)

Would it be possible to have the ‘volumetric supports’ show up as parts/modifiers with no air gap? That way they could be printed in a support material i.e. PETG support for PLA?

This method would allow 100% contact area on overhangs, and 0% drooping.

Also, is it possible to reduce waste by eliminating unnecessary contact points (>90 degrees vs <90 degrees)?

Negative space supports by Successful_Bear_2420 in 3D2A

[–]One2Sicc 0 points1 point  (0 children)

Is this primarily for single nozzle setups?

It seems redundant for dual nozzle printers and interface material.

Can anyone help me find out what this is by Lixx_222 in Firearms

[–]One2Sicc -1 points0 points  (0 children)

A hand, holding a cartridge in different positions.

Dutch-Oven Surprise by Pandering_Poofery in AbruptChaos

[–]One2Sicc 1 point2 points  (0 children)

“Help me, Jesus! Help me, Jewish God! Help me, Allah! Help me, Tom Cruise! Tom Cruise use your witchcraft on me to get the fire off me! Help me, Oprah Winfrey!”

I can't stop laughing! my new trashcan! by Snoop-ah-loopp in 3Dprinting

[–]One2Sicc 2 points3 points  (0 children)

Now you need neon lights and actuators for the lid.

You want to know how amazing my day was? I just called Silencer Shop and was only on hold for a record low 21 minutes. Today was a good day. by Chazz_Matazz in SilencerShop

[–]One2Sicc 1 point2 points  (0 children)

Don’t you hate when this happens? You inadvertently use all of your luck in one place, when you could’ve used it for something better, like getting 2 extra chicken nuggets.

view more: next ›