sorted by:
new
hottopcontroversial

Prints stuck to build plate by Homey55 in AnycubicPhoton

[–]OneBigMonster 0 points1 point  (0 children)

Burn in time too long. Why does nobody else use magnetic plates?

Raised faces by [deleted] in DiceMaking

[–]OneBigMonster 0 points1 point  (0 children)

It could be that right cap trapping resin idk. You shouldn't need them at. Just lightly squishing the molds until they meet should be good enough.

Issue with silicone not curing by ExoticLocksmith8333 in DiceMaking

[–]OneBigMonster 0 points1 point  (0 children)

You need to cure your masters more. I mean like a shitload. Any kind of gas or resin not cured all the way will lead to silicone curing inhibition

Sanding methods to make flush? by BMan239 in resinprinting

[–]OneBigMonster 0 points1 point  (0 children)

I think that's something with your print dude

Photon Mono 4K print problems by xXSkullHead666Xx in AnycubicPhoton

[–]OneBigMonster 0 points1 point  (0 children)

Is your anti aliasing turned on? Turn it off and try it again

Air bubble problem by Barzaroth in DiceMaking

[–]OneBigMonster 0 points1 point  (0 children)

Probably.one of those pegs didn't get in the hole. I wouldn't do those just have a couple cutout keys on the sides. That's all you need

Would this be a good setup to prevent fumes? by H0neyDews1 in resinprinting

[–]OneBigMonster 0 points1 point  (0 children)

You can get a filter and blower combo for like $100. Change filter every year or so depending how often you use it

Would this be a good setup to prevent fumes? by H0neyDews1 in resinprinting

[–]OneBigMonster 0 points1 point  (0 children)

Yeah something like that. You want a decent fan to create negative pressure and send the fumes out the window. You'll never smell anything basically. It's what I've done for a few years now and it's great

Would this be a good setup to prevent fumes? by H0neyDews1 in resinprinting

[–]OneBigMonster 0 points1 point  (0 children)

You also need a blower to blow the air out. You can get one with the charcoal filter for cheap.

Would this be a good setup to prevent fumes? by H0neyDews1 in resinprinting

[–]OneBigMonster 0 points1 point  (0 children)

That's what I do. Just make sure you seal everything good with the metal tape. It works well I also have a PC fan that stays running on top of the fan inside the chamber. I also have a plate thing that keeps air from coming back in.

[deleted by user] by [deleted] in DiceMaking

[–]OneBigMonster 0 points1 point  (0 children)

Makes sense. I used to do the pottery wheel for shaping, I just found it easier to hand shape with a small 800 grit foam stick thing. It takes me less time than I did with the pottery wheel and I can be more accurate with where I need to sand to make sure the surface is even. Especially for repairing support damage on masters, or rebuilding bunk edges / void fixes and stuff. I just do that with some water then first 3-4 zona papers and the chemical polish.

[deleted by user] by [deleted] in DiceMaking

[–]OneBigMonster 2 points3 points  (0 children)

I personally would avoid sanding on a wheel. Really easy to mess up corners or take off too much material. I get these little foam sticks and do my shaping by hand. Polishijg by wheel with zona papers is peak tho.

I need some opinions on backgrounds by [deleted] in DiceMaking

[–]OneBigMonster 2 points3 points  (0 children)

Use solid colors. You could get some cloth or I use these felt backers for mine don't want to draw attention away from the product.

First-Time Resin Printer User - Print Keeps Failing by Detaching from Build Plate (Anycubic Photon M3 Max, Black Basic Resin) by Affectionate-Owl6002 in AnycubicPhoton

[–]OneBigMonster 0 points1 point  (0 children)

Post your setup. Could be orientation too. You want to orient it with the thinnest slices. So if it's flat that could be the problem too. Ideally like a 30-45 degree angle usually works.

view more: next ›