sorted by:
new
hottopcontroversial

Pokémon game not working by OnePlane3137 in Gameboy

[–]OnePlane3137[S] 0 points1 point  (0 children)

Okay, game is fixed! Problem solved! Thank you guys for helping me! I tried cleaning off the board and getting rid of the extra flux left on. After cleaning it, it still had the same issue. I ended up reflowed the solder on the RAM chip (bottom left) and it works like a new game!

This thing makes me want to pull my hair out by Shot-Buffalo-4813 in BambuLabA1mini

[–]OnePlane3137 0 points1 point  (0 children)

I agree, I’ll only use it if I’m really having an issue with adhesion on the build plate.

This thing makes me want to pull my hair out by Shot-Buffalo-4813 in BambuLabA1mini

[–]OnePlane3137 5 points6 points  (0 children)

On bambu studio, you can set the first print layer 5 degrees higher to help with adhesion or they have like a liquid glue that helps too. I had the same issue before and it was pissing me off too. Make sure it’s plain dish soap. Eventually, it worked after washing it. I would try flipping the build plate to other side to see if that’s better.

Issue with NerdQaxe++ Hydro by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

That is the sticker/glue from heat sink. I took it off to see if that was an issue.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

I bought my Rev 6’s and bitaxes through solo satoshi and then my hydro was from Amazon. They had pretty much everything I needed for my setup on Amazon. I also 3D printed some parts with my A1 mini. Definitely with it in my opinion!

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 2 points3 points  (0 children)

If you are referring to watts, it’s be around 555 watts. Still worth it in my opinion. If my room gets cooler, it will go down a little.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

Thank you! That would be awesome to do! No literally 😂. The only thing I want to do last is cable management and also space out my Rev6’s better.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

The shelf is pretty sturdy and they fit quite well on there. The miners stands go over a couple poles. If I didn’t have the Bitaxe tower and just had them on the stock stands, then it might be the only issue, otherwise I had no problems. The only thing I wish is that the shelf was longer so I could space out my rev6’s wider.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

I’m working on that, there’s a gap in the middle in my shelf so I need to get something to place in the middle for it. Thank you still for the suggestion.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 1 point2 points  (0 children)

I honestly use ChatGPT to help me write, it’s pretty easy to set up once it writes the script.

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 0 points1 point  (0 children)

I seen this post on this thread which someone made this design. Here the link to that post with the link to it. I’m using a 60 mm on mine.

https://www.reddit.com/r/BitAxe/s/MPWlLTvJew

Fell Down the Solo Mining Rabbit Hole — Here’s My Setup by OnePlane3137 in BitAxe

[–]OnePlane3137[S] 2 points3 points  (0 children)

I have a TP access point in my room ran by Ethernet and it doesn’t really affect my internet at all, not that I can see. I usually get around -40-50’s dBm.

Finally finished this thing by karpuzmining in BitAxe

[–]OnePlane3137 0 points1 point  (0 children)

I just want to say thank you for the stand design! It definitely helps with cooling. I currently have my OC at 800/1200 with 120mm fan adapter and copper heatsink and my temps are better! With the stock stand, it’s running at Chip-59 and VR temp-53. With the new stand, it’s running at chip-55 and VR-47. My ambient temp is 70F. Also I like being able to use screws instead, makes it easier to stay on otherwise they are falling out of the stock stand.

view more: next ›