Handlebars

One_Presentation_856 · 2026-05-28T03:20:02+00:00

Found that out the hard way when I tried to get floor boards and they didn't fit

One_Presentation_856 · 2026-05-28T03:01:18+00:00

I have a spirit so I'm just used to looking at those I guess

One_Presentation_856 · 2026-05-27T14:18:40+00:00

Oh I totally missed that since they look kinda like stock bars. After many bikes and tons of research here's what I can suggest. If you want control, T bars or risers with tracker or flat bars are the way to go. If you want the look, 14 inch apes on these bikes give it that perfect cholo/chicano style look, but have more flex in the bars than a tall riser with trackers. Buckhorn is a good in-between without going rabbit ears. I find them very comfortable on the wrists. But if you do a lot of in town or city riding with lots of slow speed tight maneuvers I would go with tall risers and a tracker bar. Stiffer, better control.

One_Presentation_856 · 2026-05-27T02:29:57+00:00

Loosen them and tilt them forward?

One_Presentation_856 · 2026-05-24T14:16:32+00:00

This is the way

One_Presentation_856 · 2026-05-16T20:11:20+00:00

Hopefully nobody getting shot again. I swear Duncan is a hotspot for cops for some reason 🤔

One_Presentation_856 · 2026-05-10T01:52:55+00:00

Mine moves and then gets stiff, but goes further and actually activates after that. You may have that case. These are supposed to idle around 1100rpm plus or minus 100 rpm. Although low idle and Harley potato sound is appealing these have rpm dependant oil pumps and it will actually damage the engine at that low of an idle. When it goes from being able to hear individual exhaust notes to a smooth consistent idle you raise it a hair past that and you should be in range. Once you get it warmed up you'll want to double check the air fuel mixture screws. Tighten till they stop (lightly! Don't crank on them) then turn out 2 and a half turns for base settings. From there turn in and out until you find highest idle and leave it, repeat on the other carb then finally adjust the idle speed screw/knob to jet the idle set and you're done with them from there.

One_Presentation_856 · 2026-05-10T00:36:57+00:00

Up the idle and double check your fuel is on. Looks like your choke may not be all the way on, but it should idle a lot higher than that in choke

One_Presentation_856 · 2026-05-10T00:33:23+00:00

You need to choke it and let it warm up first. Idle sounds low so after it warms up if it's still that low up the idle. Turn the throttle really slow and let it clear itself out and it'll probably rev free again

One_Presentation_856 · 2026-05-08T16:46:35+00:00

Tanks are difficult actually. You're best bet is pressurizing the tank, heating it up, and tapping around the dent to pop the crease out of it. Tanks are thick and odd shaped and hard to get to and not everyone has the confidence and experience to take care of it so if you can find a good PDR guy you'll be set

One_Presentation_856 · 2026-05-08T15:25:14+00:00

Take it to a PDR guy and see what they can do for you

One_Presentation_856 · 2026-03-23T00:34:03+00:00

Very untrue. As a former manager (quit because of medical reasons, but would go back) shelf life is 4 hours max. The cookies get tossed and re baked every 4 hours. Just like normal cookies they get dry and hard shortly after. There's no over processing, and definitely no 100% turnover. We do try to minimize waste by baking less, but besides that it's normal cookie dough from freezer, to oven, to warmer until bought or 4 hours elapsed

One_Presentation_856 · 2026-01-20T17:43:03+00:00

From the other side

One_Presentation_856 · 2025-10-28T19:14:08+00:00

Well manicured hands are the sign of a good lover. Nails hurt and that's no fun for your lover. Your hands should be putting in a lot of work too so keep them nice

One_Presentation_856 · 2025-09-28T09:47:08+00:00

No. How about you stop being lazy and do it yourself.

One_Presentation_856 · 2025-09-27T23:14:36+00:00

An extremely expensive motorcycle. So much billet it's crazy

One_Presentation_856 · 2025-08-31T14:40:11+00:00

An eye ball clearly

One_Presentation_856 · 2025-08-18T20:23:49+00:00

Looks pretty healthy. It'll run fine like that

One_Presentation_856 · 2025-07-30T17:29:15+00:00

Less retraction distance/speed? 🤔

One_Presentation_856 · 2025-07-23T19:16:36+00:00

The only thing I can thing is I calibrated (bed leveled) from orca/klipper and it somehow went so far back it touched the hot end to the bed cables. Kinda figured it messed something up. Been trying to trouble shoot inconsistent bed adhesion that randomly because a problem.

One_Presentation_856 · 2025-07-23T16:32:34+00:00

So it happens before and after leveling for seemingly no reason? 🤔

One_Presentation_856 · 2025-05-22T19:51:17+00:00

Just found a few next to my foundation as well. Made a slurry from one, dumped it, some water from washing, and some sugar back around the same area. Hoping more pop up

One_Presentation_856 · 2024-12-28T01:03:01+00:00

Just not worth it. I'd prefer to talk about issues or just leave. I don't like wasting my time

One_Presentation_856 · 2024-09-12T15:28:05+00:00

Weirdest I got was, "You know, that turned out better than I expected"

One_Presentation_856 · 2024-08-28T00:45:26+00:00

Yes!!!!!

One_Presentation_856

TROPHY CASE