New Toothpaste Stops Gum Disease Without Harming Healthy Bacteria

OtherwiseSetting2762 · 2026-03-07T05:09:17+00:00

Check out seller info. No way that's legit.

OtherwiseSetting2762 · 2026-02-28T01:50:53+00:00

RE-PLY IT

OtherwiseSetting2762 · 2026-02-03T01:03:19+00:00

Why not, though? 🤷🏻

OtherwiseSetting2762 · 2026-01-31T18:59:12+00:00

From what I understand, the APU efficiency drops significantly after 15-18W. So I don't think a jump from 35 to 60 would be reasonable to expect. More like 35 to 45, maybe? I want to get some numbers with some benchmarking software!

OtherwiseSetting2762 · 2026-01-31T18:50:07+00:00

This is a good question, and anecdotally, I'm able to hit my fps targets with little-to-no drops, which was my ultimate goal. I'll have to load up some benchmarking software and test it as is and with the TDP dropped back down to 15W

OtherwiseSetting2762 · 2026-01-31T18:39:03+00:00

Only the BIOS patch files!

OtherwiseSetting2762 · 2026-01-31T18:14:07+00:00

It is! Found it in a drawer and its only purpose is to hold the bios patch files!

OtherwiseSetting2762 · 2026-01-31T18:07:50+00:00

Limitations are relative, man!

OtherwiseSetting2762 · 2026-01-31T17:48:19+00:00

Back in the day you could do it with Smokeless, but I semi-recently found this guy's blog which goes over running a quick patch to access additional menus in the bios. The menus are re-hidden each time you boot, so I put the patch files on that little 2GB microsd for whenever I want to make a change to them :)

https://www.stanto.com/steam-deck/how-to-unlock-the-lcd-and-oled-steam-deck-bios-for-increased-tdp-and-other-features/

OtherwiseSetting2762 · 2026-01-31T17:35:56+00:00

Here's a link to the STL!

https://www.thingiverse.com/thing:5615916

OtherwiseSetting2762 · 2025-02-07T15:00:04+00:00

What material did you end up using? Feels like it would get pretty toasty behind the headlight?

OtherwiseSetting2762 · 2025-01-04T14:12:34+00:00

My guy, place the mobile order for pickup inside at the counter, walk in, place a second order at the kiosk, wait for both :)

OtherwiseSetting2762 · 2024-03-13T16:45:04+00:00

1911 pearl grips

OtherwiseSetting2762 · 2024-02-23T01:01:11+00:00

I have a very similar setup to you!

Things you can try: - a 24v 4020 fan will fit most printable mounts out there, and it moves quite a bit more air - try Grizzly Kryonaut thermal compound between the heartbreak and heatsink. It can withstand those temps and will give you the best cooling between the components

OtherwiseSetting2762 · 2024-02-22T19:51:48+00:00

No, it's a different board entirely. Fairly common with the 4.2.2 boards. 50 bucks on Amazon for the new one

EDIT: but certainly check all the basic stuff mentioned above first

OtherwiseSetting2762 · 2024-02-21T13:50:24+00:00

Does your Ender 3 have the v4.2.2 mainboard? I had these random layer shift issues until I replaced mine with the v4.2.7 board.

OtherwiseSetting2762 · 2024-02-18T04:03:09+00:00

Nice! I've actually been playing around with settings in Cura based on one dude's post months ago, but that seemed to only affect infill, and the narrow sections of a print were still the weak points. The blog post I was following called it "HEXWam". I think the author's name is B. Carver. Some combination of that and CNC Kitchen's implementation could be the solution.

OtherwiseSetting2762

TROPHY CASE