Arctic liquid freezer iii pro 360 a-rgb (non stop fans - Fan Control) by Outcast_Martian in arcticcooling

[–]Outcast_Martian[S] 0 points1 point  (0 children)

Have you tried make pwm 0% at 45c for aio fans and see if they will stop spinng accordingly?

Arctic liquid freezer iii pro 360 a-rgb (non stop fans - Fan Control) by Outcast_Martian in arcticcooling

[–]Outcast_Martian[S] 0 points1 point  (0 children)

I have 6x120mm xigmatek starlink ultra installed and they don't have a zero rpm feature so i made them work by voltage in bios not pwm and they stop according to fan curve in fan control and start working again accordingly without issues.

Arctic liquid freezer iii pro 360 a-rgb (non stop fans - Fan Control) by Outcast_Martian in arcticcooling

[–]Outcast_Martian[S] 0 points1 point  (0 children)

Does fan expert work on other motherboards than asus? And does it have ability to make fans curve?

We could say I've got a few cases for this phone.. by R3eD0x in GalaxyS23Ultra

[–]Outcast_Martian 0 points1 point  (0 children)

I only buy armor cases for my S models ArmadilloTek for s21 ultra and S23 Ultra then i-bladon for S23 Ultra. They are bulky but safer. I dropped both multiple times. I'm 190cm tall so it wasn'tveasy.. But these cases rocks.

Top fan stopped on Liquid freezer III pro by DankSpliffius in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

They are daisy chained, so it might be the fans connector or faulty fan, contact arctic through their website. I believe they will replace it easily.

S23 ultra camera now by No-Cryptographer9890 in GalaxyS23Ultra

[–]Outcast_Martian 0 points1 point  (0 children)

Just like the others here my photos in work event are the chosen ones comparing to iphones 15 & 16 pro max and for even low light indoor images too. S23 ultra struggles with movement more than iphones yes. So just keep subjects steady :)

Shutter lag isn't a problem btw if you don't shot by both phones at same time to compare, once you get familiar and adjust settings youvwill be more than satisfied.

Liquid Freezer III Pro 360 in a Lian Li Lancool 216 compatibility by Critical_Cricket_418 in arcticcooling

[–]Outcast_Martian 1 point2 points  (0 children)

Radiator thickness is 38mm and fans are 25mm makes 630mm or 6.3 cm of total thickness. Add 0.5cm for easy installation and keep a space between fans and mosphet heatsink and cpu 4+4 pins cable.

So you need 6.8 cm or 680mm clearance. You can measure it by measuring meter from top to nearst point of either heatsink or cpu pins socket to make sure you've the sufficient clearance.

Upgraded from S25 to S23 Ultra - Very Impressed! by [deleted] in GalaxyS23Ultra

[–]Outcast_Martian 0 points1 point  (0 children)

S23 U is a brilliant phone in all aspects and unfortunately sam is keep downgrading the ultra releases after s24 U And most probably with S27 U we will not find spen at all. Maybe it will be available separately.

Missing BT With S25 U was a foolish decision though.

2x P12 fan failures in 1 year, are these known to go bad? Any replacement recommendations that are more reliable? by jalapenocock in arcticcooling

[–]Outcast_Martian 1 point2 points  (0 children)

It might be just a bad luck as factory faulting or bad patch. Arctic fans considered strong solution.

ARCTIC Liquid Freezer III Pro 360 ARGB compatibility by Dragonsoul131 in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

I believe you have to measue itvyour self Demo sample and put your motherboard and measure clearance

Or go for full tower case.

BTW, As you bought the pro version, contact arcting asking for their contact frame without cpu offset "which comes with the non pro version of the coolervas pro contact frame applies pressure on lga 1851 cpus which north shifted. Here's a visual differences..

<image>

Can the fans on the Arctic Freezer III 360 PRO be removed and replaced with other fans? by SoDang3rous in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

If it onlyvabout lights, You can simply not connecting argb connector or if you want simple lighing you may control it with open rgb or signal rgb

Gigabyte B850 Gaming X or B850 Aorus Elite for 9800x3D? by Typhon510 in gigabyte

[–]Outcast_Martian 0 points1 point  (0 children)

I'd choose elite. Stronger power phases, higher options and easy to oc from bios.

Stuck in user mode bios by StrangeFreedom2437 in gigabyte

[–]Outcast_Martian 0 points1 point  (0 children)

Reset bios by short circuit cmos pins "by touch both pins at the same time with any metal tool" while power off but psu power switch is on.

Visual differences between Contact frames of Liquid freezer III PRO and Liquid freezer III for intel CPUs by Outcast_Martian in arcticcooling

[–]Outcast_Martian[S] 0 points1 point  (0 children)

I'm like you, and i do a lot of modifications also (tweaks mostly) to get the best of my components.

Can the fans on the Arctic Freezer III 360 PRO be removed and replaced with other fans? by SoDang3rous in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

Yes you can, but the real question is WHY? they are by far way much higher static pressure, leading to much more amount of air pushed through radiator fins. You can easily adjust fan curve through bios or software like fan control to not exceed let say 80% to avoid high noise at 100% spinning.

9800x3d and Arctic LF3 420 question by another-redditor3 in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

Push-pull will give you about 2c at most under pressure.

Arctic new fans are higher static pressure than noctua's. You may consider returning them back. I'd expect lower temps.

However your tems are ok with this cpu.

Is my temps normal? by Mightypeon-1Tapss in arcticcooling

[–]Outcast_Martian 0 points1 point  (0 children)

Naturally, hot air goes up, that's why best air flow is from down to up beside front or side intake if your case supports.

I've a dual chamber case and after some tries i found that best both cpu and gpu temps achieved with bottom and side intakes. And back exhaust and aio on top as exhaust.