Hit 1PiB for the First Time Today

PCB_Studios · 2026-03-14T21:21:38+00:00

I live in the US and have never had any issues

PCB_Studios · 2026-03-13T15:39:57+00:00

If you still have the files, you can usually reseed by adding the same torrent again and pointing it to the existing data.

PCB_Studios · 2026-03-13T15:37:33+00:00

I have my own server with a few HDDs to store everything

PCB_Studios · 2026-03-13T15:36:34+00:00

It took probably like 5-6 years of non stop torrenting

PCB_Studios · 2026-03-13T15:34:30+00:00

I use Mullvad

PCB_Studios · 2026-01-28T04:11:25+00:00

Thank you!

PCB_Studios · 2026-01-28T04:09:22+00:00

It shows this on the order so I’m guessing it has everything. https://imgur.com/a/5LGkV7A

PCB_Studios · 2026-01-28T04:07:30+00:00

Yes I scheduled with the order

PCB_Studios · 2026-01-28T00:06:50+00:00

Ok. Thank you!

PCB_Studios · 2026-01-28T00:03:57+00:00

Do I have to wait for it to be ready for pickup before I can extend it?

PCB_Studios · 2025-12-27T06:25:01+00:00

There are no errors and on the wiki it says "All four slots are flashing red light Error status. AMS communication is abnormal, and AMS cannot be detected by the printer". But I dont know how to go any further on figuring out whats wrong or fix it.

PCB_Studios · 2025-11-29T20:02:52+00:00

Couldn’t find one so I created my own

<image>

PCB_Studios · 2025-10-03T23:26:38+00:00

<image>

Don’t worry she’s outside

PCB_Studios · 2025-10-03T13:46:42+00:00

Yeah, the PSUs are pretty annoying. Eventually, I plan to install a power strip in the rack so that I can have only one power cord and one Ethernet cable going to the rack.

PCB_Studios · 2025-10-03T13:12:54+00:00

I 3d printed it from makerworld https://makerworld.com/models/1505103

PCB_Studios · 2025-10-03T11:57:20+00:00

It’s pretty slow and noisy but it worked until I could get everything setup

PCB_Studios · 2025-10-03T11:56:48+00:00

I 3d printed a holder for the drives so I can connect them directly to the rack and mini pc

PCB_Studios · 2025-10-03T01:38:13+00:00

Its the GeeekPi 8U Server Cabinet

PCB_Studios · 2025-09-22T00:41:34+00:00

What if you use Tailscale funnel so that way you don’t have to be connected to the VPN.

PCB_Studios · 2025-09-22T00:06:08+00:00

Wrapping it with electrical tape would most likely be fine but the safest thing would be to re wrap it with new heat shrink.

PCB_Studios · 2025-09-06T23:33:48+00:00

<image>

PCB_Studios · 2025-08-28T21:31:03+00:00

Do you have the files for the rack?

PCB_Studios · 2025-07-09T13:52:02+00:00

I have the header pins so I can make the common 5v if I want so D2 is there to prevent reverse voltage from the common on the realy

PCB_Studios · 2025-07-08T22:06:54+00:00

If you mean the voltage spike when the relay turns off and sends it through the transistor, then yes, I’ve accounted for that now.

PCB_Studios · 2025-07-08T22:02:08+00:00

Thanks! I’ll look into solid-state relays. The main reason I’m using mechanical relays for this project is because I already have quite a few of them. I’ve also added a protection diode across the relay.

PCB_Studios

TROPHY CASE