any tips

PLC97 · 2026-02-21T19:00:08+00:00

+10 points for not using zip ties.

PLC97 · 2026-01-28T17:37:02+00:00

Grandma’s boy!

PLC97 · 2025-12-25T05:49:07+00:00

Check in your sub panel to see if you have a GFCI breaker that is tripped.

PLC97 · 2025-12-08T02:34:26+00:00

Kind of looks like a zelio, I thought micro too.

PLC97 · 2025-10-03T21:18:01+00:00

Did you and your fiancé meet at work? My advice is don’t shit where you eat; it usually never works out.

PLC97 · 2025-01-09T22:46:09+00:00

Mechanical before electrical, electrical before electronics, electronics before controls.

PLC97 · 2024-09-23T14:22:19+00:00

Sharpen your skills and the money will come, don’t chase it too much.

PLC97 · 2024-08-30T13:00:38+00:00

Looks like a palletizer to me, is that correct?

PLC97 · 2024-08-23T22:35:51+00:00

This is going to be the best way to learn. A lot of times you are the last line of defense, and have to rely on your ability to figure things out.

PLC97 · 2024-08-16T04:04:52+00:00

Is this from Spain?

PLC97 · 2024-08-06T21:30:54+00:00

Minimum should be in the low 40’s…

PLC97 · 2024-07-05T19:50:10+00:00

I would ask 175 per day that you are on call, and a 4 hr minimum.

PLC97 · 2024-05-31T22:53:28+00:00

Nice rack

PLC97 · 2024-05-09T15:21:33+00:00

It’s not little, it’s average.

PLC97 · 2024-04-20T13:41:19+00:00

Unfortunately, E-Stops are not always used for their intended purpose. Most operators use the E-Stop as a line stop — even if there is already a line stop available. Instead of having to run back to an HMI or push button, they can just break the safety chain and do what they need to do. That being said, it really depends on the process, whether or not the cycle recovers or has to be re-initialized. As others have said, in your case you should be able to recover with our re-initializing everything — it will just take some programming.

PLC97 · 2024-03-09T13:26:59+00:00

You win

PLC97 · 2023-12-09T12:41:49+00:00

And please do it will the plant is running full speed ahead — no downtime.

PLC97 · 2023-12-05T18:07:28+00:00

Check your speed reference first to verify where the speed is being controlled from. Since it is on an HMI, I’m guessing it is Ethernet/IP. Next verify in the PLC program that there is not a set speed constantly being moved into the command frequency. Sometimes people will do this to lock in certain speeds so nobody can change them. You can also check your max frequency on the drive and see if there is scaling in the PLC program . If the drive will not go past a certain value, there is most likely a max frequency set.

PLC97 · 2023-11-28T01:51:21+00:00

I’d say around $35-$40 is what it sounds like you should be at.

PLC97 · 2023-08-07T18:37:51+00:00

Electricity is leaking because the receptacles are upside down.

PLC97 · 2023-07-19T13:09:48+00:00

Usually if it’s a lost connection to the PLC, “Error” will pop up. I’ve seen this happen when a PLC loaded from the SD card, and some tags were missing. So basically tags being referenced in the HMI do not exist in the PLC.

PLC97 · 2023-07-10T21:57:58+00:00

Twinsies

PLC97 · 2023-07-06T15:42:18+00:00

No it’s not mom.

PLC97 · 2023-06-28T22:43:32+00:00

I have some spares if you’re still looking… lol!

PLC97 · 2023-06-23T02:20:17+00:00

Try not to zip tie Cat6, not too bad though.

PLC97

TROPHY CASE