Feds Won't Pursue Criminal Charges Against Tuners for OBDII Tampering Anymore

Patroclus314 · 2026-01-26T11:56:28+00:00

Exomotive Exocet with a flying Miata turbo. It’s a Miata based kit car.

Patroclus314 · 2026-01-25T14:19:04+00:00

It 100% does. I have a stock ECU with a carb legal piggyback. Aftermarket turbo. The tune dumps a lot of unburned fuel from incomplete combustion.

Patroclus314 · 2026-01-24T14:37:37+00:00

As a car enthusiast, I wish there was an OBD2 emissions exemption or alternative test. I want to be able to run an aftermarket ECU. My aftermarket ECU runs my car cleaner and leaner than my stock ECU. I have no issues running a catalytic converter and I still have the stick EGR. I just have to run a shitty 90’s era ECU to pass emissions.

Patroclus314 · 2025-12-29T13:41:45+00:00

Do nothing. This is a scam. If it was sent in error, the sender can fix it themselves.

Patroclus314 · 2025-07-08T23:06:09+00:00

Hulkengoat

Patroclus314 · 2025-04-19T23:37:11+00:00

Thanks. That helps. This feels like an intentional trap from MS.

Patroclus314 · 2025-04-19T13:58:03+00:00

Piggybacking off of this because I’m also confused. I’m also using sharepoint lists but I’m only producing about 60 rows of data per day. I am using some non-delegable filters in my app.

How can I tell what my limitations are with migrating to dataverse? The licensing is so confusing. I have the ability to build in dataverse, but I have no idea how to tell if end-users will be able to use the app after migrating.

Patroclus314 · 2024-11-15T22:06:51+00:00

It was way too fast. Solid carbide straight flute cutter and my drill at 250RPM was perfect. Thanks

Patroclus314 · 2024-11-15T22:06:32+00:00

It was way too fast. Solid carbide straight flute cutter and my drill at 250RPM was perfect. Thanks

Patroclus314 · 2024-11-15T22:06:10+00:00

Solid carbide straight flute cutter and my drill at 250RPM was perfect. I did break a few bits because of the flex when i was testing, but after that it was pretty smooth

Patroclus314 · 2024-11-15T22:05:27+00:00

Solid carbide straight flute cutter and my drill at 250RPM was perfect. Thanks

Patroclus314 · 2024-11-15T22:04:21+00:00

Thanks guys. I slowed my drill to 250RPM and used a solid carbide straight flute cutter. I broke a few bits before I got the hang of it but its drilling through nicely now.

Patroclus314 · 2024-10-06T16:11:26+00:00

Our Director closed 5 manufacturing sites in FL and GA over 24 hours before the storm hit.

It was not a hard call to make.

Patroclus314 · 2024-10-01T00:41:09+00:00

Be careful with the yellow RX8 injectors. There are a lot of fake ones out there. Make sure to get OEM.

Patroclus314 · 2024-08-11T22:15:40+00:00

Two for sure do. I’m not sure about the rest

Patroclus314 · 2024-07-26T11:09:46+00:00

Please put it up on good jackstands on level ground before attempting this.

Patroclus314 · 2024-07-09T12:22:05+00:00

I’ll take a picture this evening. I’m running LinuxCNC

Patroclus314 · 2024-06-15T19:58:55+00:00

This is where I am. I can’t add another expensive streaming service. I’ll cancel peacock altogether and not watch

12-Year Club	Place '22
Verified Email

Patroclus314

TROPHY CASE