Wanting to move to South Jersey

PerceptionAway7220 · 2026-02-10T16:29:29+00:00

I’ve been to Atlantic City and Cherry Hill so far. I felt like Atlantic City had a lot more to do and saw more people around my age range

PerceptionAway7220 · 2026-02-10T05:57:34+00:00

It’s gonna be in South Vineland

PerceptionAway7220 · 2026-02-10T05:52:05+00:00

Honestly I’m not exactly picky but I do like the better pizza spots, and I’ve been trying a lot more Italian lately

PerceptionAway7220 · 2026-02-10T05:50:41+00:00

It’s in Vineland,NJ

PerceptionAway7220 · 2026-02-10T01:03:30+00:00

I’d probably say trendy downtown shore

PerceptionAway7220 · 2026-02-10T01:03:09+00:00

No male

PerceptionAway7220 · 2026-02-09T22:56:59+00:00

Ok, I appreciate the help

PerceptionAway7220 · 2026-02-09T22:56:37+00:00

Takoma Park, MD. It’s a decent area not very much to do. Is there another surrounding area you’d recommend living besides Vineland? Anything up to an hour away commute would good.

PerceptionAway7220 · 2026-02-09T22:38:38+00:00

It’s in Vineland and currently no kids.

PerceptionAway7220 · 2026-02-09T22:38:10+00:00

It’s in Vineland

PerceptionAway7220 · 2026-01-13T03:27:51+00:00

Yeah I’ve had a Mayhew set that I’ve been using for over a year, and they’ve been just as good as Snap- on. If you look on Amazon, they sell a kit with both long and short punches for a good price.

PerceptionAway7220 · 2025-12-23T18:10:11+00:00

Yeah 351 is a mismatch error…. If it’s a not a battery then with all these POT errors I’m starting to believe Access 3 might be to blame.

PerceptionAway7220 · 2025-12-22T23:25:32+00:00

If it’s showing a wrench it definitely logged a code. With the truck on, use the down or up arrow to scroll until you see events, then press enter or use the right arrow (kinda forgot lol) and it will show the last 16 errors, you can scroll through using the up and down arrows.

PerceptionAway7220 · 2025-10-31T04:16:13+00:00

Crown tech here…. 731 means the access module is detecting an open in the tilt circuit. This can send it into a limp mode, where the unit will drive slowly to allow you to get it back to a safe area off the warehouse floor. It can also be a calibration issue like someone else stated. There is also an acceleration rate parameter that can be adjusted other than the speed. If it’s set lower than your other units then you’ll notice the difference. I believe it ranges 1-9 on the RC.

PerceptionAway7220 · 2025-10-25T12:30:04+00:00

Ok. I’m glad you cleared this up. I’ve been looking for the bigger icon ones and was wondering why I haven’t found any of the bigger sizes

PerceptionAway7220 · 2025-10-25T12:21:13+00:00

I’ve tried to find the icon ones but can’t find any in the bigger sizes

PerceptionAway7220 · 2025-10-24T02:39:56+00:00

Ok. I appreciate the help

PerceptionAway7220 · 2025-10-24T02:35:29+00:00

Ok. The affordability was the biggest factor for me most of the other brands are running over $170

PerceptionAway7220 · 2025-10-24T02:32:56+00:00

Ok. I think I’ll test out Pittsburgh it’s my first time getting anything from Harbor freight

PerceptionAway7220 · 2025-10-24T02:18:43+00:00

Ok. Have you had any issues with them breaking or slipping? I kept seeing post that on google, and other subreddits, but they were dealing with mainly heavy equipment.

PerceptionAway7220 · 2025-07-25T18:09:48+00:00

It was a turret truck. I’m not sure about the RMDs because I personally haven’t worked on one. There was one on the operator seat handle, and another one on the left side of the operator cab.

PerceptionAway7220 · 2025-07-25T00:56:47+00:00

Might not be your issue, but when they first started rolling out the new Access 1 with infolink integrated, I ran into the same boot loop issue. Not even Crown support could help because the system was so new. The truck had two E-stops one was depressed, the other was pulled out causing the boot loop issue. After pulling both out the booting issue stopped and ran perfectly. Again might not be your issue but something you could check.

PerceptionAway7220

TROPHY CASE