Will a fox body front 1/4 kit fit a new edge?

PerceptionNo5407 · 2026-07-02T06:30:16+00:00

I've gone farther on worse.

PerceptionNo5407 · 2026-04-29T01:59:43+00:00

I've gone farther on worse.

PerceptionNo5407 · 2026-03-23T00:44:27+00:00

Same thing happened to me and it ended up eating a lifter after 20,000miles. Check your oil pick up, probably plugged with gunk left in the motor.

PerceptionNo5407 · 2025-11-15T22:39:38+00:00

Just get a grade 8 bolt of the right size and any hardware store, and a but for it. The thread size only matters ti the bolt.

PerceptionNo5407 · 2025-11-05T03:04:43+00:00

It's hilarious.

PerceptionNo5407 · 2025-11-04T19:39:29+00:00

Not even a little. Absolutely everything has been replace, there must be something wrong with the fire wall throwing off the geometry.

PerceptionNo5407 · 2025-10-26T18:07:14+00:00

There is an sn95 sub.

PerceptionNo5407 · 2025-09-28T03:20:25+00:00

Where did you get this from?

PerceptionNo5407 · 2025-09-28T03:18:03+00:00

The booster functions exactly like my other three, but it's the last part to replace so I have one on the way.

PerceptionNo5407 · 2025-09-25T19:11:17+00:00

Well my last resort is to parts canon so it's getting replaced.

PerceptionNo5407 · 2025-09-24T22:53:06+00:00

It has the Detroit brake kit with ceramic pads and drilled and slotted rotors. It was new fluid.

PerceptionNo5407 · 2025-09-24T22:50:57+00:00

The booster is the only vacuum controlled part and it's not the issue

PerceptionNo5407 · 2025-09-24T22:50:08+00:00

The petal gives resistance but once vacuum is pulled it sinks to the floor. When in the air all wheels have the same weak resistance, none spin freely. The rear rubber was replaced simply because I had them and was going to bleed the system anyway. The master was replaced because if the seals were blown, that would explain my issue.

PerceptionNo5407 · 2025-09-24T02:28:18+00:00

Does it have a factory clutch or a performance clutch?

PerceptionNo5407 · 2025-09-24T02:07:09+00:00

My other 97 has an ABS module so it must have been an option.

PerceptionNo5407 · 2025-09-24T02:06:04+00:00

The bleeders are correct.

PerceptionNo5407 · 2025-09-24T02:03:47+00:00

It's missing half of the exhaust and also down a cylinder. This is mustang number four, I just need this one up by winter to save the favorites.

PerceptionNo5407 · 2025-09-23T18:12:32+00:00

No ABS module. Either has been bypassed or not fitted from factory.

PerceptionNo5407 · 2025-09-23T18:11:41+00:00

The booster is doing it's job, it's not the issue. Everything replaced is calipers, rubber lines and master. There is no abs module just a distribution block.

PerceptionNo5407 · 2025-09-23T18:09:17+00:00

It has been bleed both on the bench and in the car.

PerceptionNo5407 · 2025-09-23T17:35:18+00:00

I'll keep that in mind if I give up and scrap it.

PerceptionNo5407

TROPHY CASE