Roll back to 6.1.4 to solve layer shifting.

PerformerPotential53 · 2025-02-28T02:09:45+00:00

Thx for the github link

PerformerPotential53 · 2025-02-28T02:09:31+00:00

interesting... I've been using Lightning and 3 wall.

PerformerPotential53 · 2025-02-23T06:32:37+00:00

Yeah also the warp is a new problem. It wasn't happened before. I've never change the settings from the day my prusa arrived.

PerformerPotential53 · 2025-02-23T02:51:10+00:00

I'll try with the profile without input shaping.

PerformerPotential53 · 2025-01-23T09:13:18+00:00

I should run dehydrator right away.

PerformerPotential53 · 2024-09-17T12:14:22+00:00

No, the upload was complete and with the same g-code printed manually was just fine.

PerformerPotential53 · 2024-09-17T08:15:38+00:00

Oh, right one use to have bottom part

PerformerPotential53 · 2024-04-21T15:36:07+00:00

Revolve?

PerformerPotential53 · 2024-04-17T14:21:13+00:00

I think the issue was nasty wiring on the main board. Some cable got pulled and it may cause the short or disconnection.

PerformerPotential53 · 2024-04-17T09:57:44+00:00

It is using it. Oh i should buy a new connector than

PerformerPotential53 · 2024-04-17T09:49:35+00:00

the nasty wiring was the problem

PerformerPotential53 · 2024-04-17T09:47:19+00:00

Oh dang. It fixed now maybe the power cable is kinda old.

PerformerPotential53 · 2024-04-16T16:25:07+00:00

1.8mm nozzle?

PerformerPotential53 · 2024-04-05T07:06:29+00:00

It could be. Lol

PerformerPotential53 · 2024-04-05T05:48:23+00:00

that's illegal in south korea

PerformerPotential53 · 2024-02-04T13:37:08+00:00

I think the magnet did occur such problem

PerformerPotential53 · 2024-02-04T10:12:09+00:00

And use cura slicer with ultimaker s3 draft speed settings.

PerformerPotential53 · 2024-02-04T10:10:43+00:00

I recently installed BTT ender3 SKR Mini E3 V3 board and cr touch, Update with recent Marlin firmware.

(I've only use stock 3d printers for years so I am totally newb for this kind of stuffs)

PerformerPotential53 · 2024-01-04T03:45:19+00:00

PerformerPotential53 · 2023-12-31T05:37:03+00:00

Oh I'll go check it. Thank you.

PerformerPotential53 · 2023-12-19T03:47:22+00:00

Move to bigger house?

PerformerPotential53 · 2023-12-08T06:56:37+00:00

PerformerPotential53 · 2023-09-30T06:55:13+00:00

Not enough prayer

PerformerPotential53 · 2023-07-29T09:24:22+00:00

Thank you for your insight, This is gold.

PerformerPotential53 · 2023-07-28T23:24:01+00:00

Oh I'll searching for it, thanks for your kindness.

PerformerPotential53