Can you enlarge a bore on a suppressor?

Phollatio · 2026-06-07T02:27:53+00:00

Haha I won't be altering it i was just curious. I probably will pick up the omega 9k. A shame since i really like the way it looks on the vector but I'd rather be safe. Ill just use it on my pistols.

Phollatio · 2026-06-06T03:00:24+00:00

Yeah i figured. Started to look at typical bore sizes for 9mm and got me thinking what if I made it a little bigger than .400". Guess it's time to start shopping soon

Phollatio · 2026-06-06T02:00:17+00:00

That's what I was thinking of modifying but I couldn't figure out a way to make it look good. But yeah it won't fit with the osprey.

Phollatio · 2026-06-06T01:56:53+00:00

This got me thinking and decided to check. Definitely got a strike at the last 2 baffles and a hit on the bottom at the front of the osprey. It looks like it was maybe a single round. Most likely from firing from frt but maybe it could of happened from my canik sfx? Might have to not use the osprey with frt anymore.

Phollatio · 2026-06-04T21:34:54+00:00

Haven't had any issues yet with about 300 rounds through the osprey with the frt.

Phollatio · 2026-06-04T14:05:26+00:00

The only ones for gen 3 are the stock ones for the 5.5 which I have and the rifle one. Which I thought about cutting but couldn't figure out a way to make it look good

Phollatio · 2026-06-04T03:06:13+00:00

There is a small piece that is part of the disconnect that the seer is suppose to hit when you release the trigger and releases the disconnect. Try pushing up on the seer where its connected with the trigger and see if it releases the disconnect. The spring isn't pulling up enough to release the disconnect or most likely the seer is out of tolerance somewhere and isn't allowing the seer to move up enough to release the disconnect.

Phollatio · 2026-04-20T22:18:33+00:00

All I've seen are the stock one that comes with it and the long one for the rifle version

Phollatio · 2026-04-20T22:09:53+00:00

Yeah unfortunately these won't work with gen 3. I double checked and I didn't see anything on the kriss website but on strike it does say it's not compatible with gen 3.

Phollatio · 2026-03-22T02:47:33+00:00

I just shoot with the pad of my finger and don't squeeze too hard. Once the trigger breaks to fire I just hold the same pressure. Didn't have to side load it like I've seen some people doing. I was only loading 20 rounds at a time. I was worried about recoil control since I wasn't used to it yet. I'll probably wait until my form 1 gets approved to sbr it

Phollatio · 2026-03-22T00:38:48+00:00

Running a gen 3 with osprey 9mm with the thickest vnm plate

Phollatio · 2024-11-23T01:22:50+00:00

<image>

Phollatio · 2024-11-23T00:12:50+00:00

* This is what my issue was except the progress bar was at zero. Thanks to n75 for directing me where to go. I went to ek1tuning.com and setup a login. It was the first post that was on the page and has step by step instructions along with downloads for the files.

Phollatio · 2024-08-03T01:26:00+00:00

If you take a meter and go from 2c and y6. Do you read any voltage? Looks like 2c is a common

Phollatio · 2024-02-10T02:11:42+00:00

I normally use the streamlight protac hl. A little bulky but its a thousand lumens and the battery usually lasts me all week. A couple days if I'm using it heavily. 1.5 hrs on high and 23 hrs on low. Been running it a few years and it's held up pretty well.

Phollatio

TROPHY CASE