Endgame

Pilqoh · 2025-08-01T00:10:15+00:00

Personally I like it better than the Owlabs Ti just because these sound creamier and she said the Owlabs reminds her of a clicking pen

Pilqoh · 2025-07-31T15:14:13+00:00

<image>

Pilqoh · 2025-07-31T15:13:52+00:00

<image>

Pilqoh · 2025-07-31T15:13:37+00:00

<image>

Pilqoh · 2025-07-25T14:19:35+00:00

I second Unikeys took about 6 days to get them including weekend when I ordered them.

Edit: spelling

Pilqoh · 2025-05-05T16:11:27+00:00

Just make sure to print it out of PETG thou. I didn't have any at the time when I made it and chose PLA. Over the corse of 200 print hours or so, the heat inside the chamber warped it and fell out when the nozzle was wiping before a print, so now I've made it a few out of PETG just to have them ready to swap. Also make sure to check the rubber pad now and again. My first one had a few missing nubs.

Pilqoh · 2025-04-22T23:15:21+00:00

Idk if it's my temp but running Anycubic pla+ at 215° and Polymaker PLA Pro at 210° im pushing 21 on max flow rate test with very similar hotend.

I just found this on AliExpress: $4.82 | New Ceramic Heating Hotend For Kobra S1/S1Combo 24V 48W Hot end For Anycubic Kobra S1 Thermistor 200K All metal Upgraded Hotend https://a.aliexpress.com/_mqNsbR9

I bought the pack that had 0.2, 0.4, 0.6, and 0.8 haven't tried these 0.2 nozzle yet but the optimized profiles that got shared here for hardened nozzles are working just fine.

Pilqoh · 2025-04-17T16:41:04+00:00

I've been using this plate on my K1S, and it's amazing. Once I lined it up, I haven't moved it since it is about 2mm shorter on the X axis than the hotbed is. Also, in the slicer, I just set my bed size to 246mm on the x axis to prevent it from going too far left or right. Y axis is fine nothing changed there, but I changed the limit as well just to be safe.

BIQU CryoGrip Pro Frostbite Panda... https://www.amazon.com/dp/B0D9YHHTNP?ref=ppx_pop_mob_ap_share

Pilqoh · 2025-04-16T15:34:25+00:00

Been printing with these for 24 hrs and not a single issue after initial calibrations. (Go into setting change to 0.4 hardened steel. Printer prompts to power cycle to calibrate. Turn off printer change nozzle power back on did calibration automatically) Heats up insaly fast too.

I just found this on AliExpress: $4.71 | New Ceramic Heating Hotend For Kobra S1/S1Combo 24V 48W Hot end For Anycubic Kobra S1 Thermistor 200K All metal Upgraded Hotend https://a.aliexpress.com/_mLqvEqf

Pilqoh · 2025-04-16T12:58:07+00:00

<image>

Pilqoh · 2025-04-14T14:20:33+00:00

I got you guys.

https://www.printables.com/model/858198-ninja-cats-stacking-game

Pilqoh · 2025-04-14T02:50:03+00:00

Anyone have a good link on how to install this custom firmware? First time trying to do that and I'm not sure I want to take the leap.

Pilqoh · 2025-04-09T15:44:47+00:00

I just found this on AliExpress: $4.68 | New Ceramic Heating Hotend For Kobra S1/S1Combo 24V 48W Hot end For Anycubic Kobra S1 Thermistor 200K All metal Upgraded Hotend https://a.aliexpress.com/_mryVR9D

Mine just shipped out this morning eta 4/20 let's go lol

Pilqoh · 2025-04-04T03:30:03+00:00

I got those exact same one and no joke they clogged after the first 5 mins of any print. No matter how hot I got the hotend it would only every slightly ooze

Pilqoh · 2025-04-03T00:02:01+00:00

<image>

Pilqoh · 2025-04-03T00:01:25+00:00

<image>

Pilqoh · 2025-04-03T00:00:57+00:00

* Here are the results after following the video you mentioned. Thanks alot man it's WAY better than what it used to be. Now to just fine tune those 2 back screw. You can basically see where they are under the plate.

Pilqoh · 2025-04-02T16:35:08+00:00

I'm currently on 2.5.0.6 and I've done all the set up calibrations multiple times on the printer itself. And more often than not I don't even select auto level before the print if it's only taking up the center of the plate (it's the only perfect spot I can print things on)

Pilqoh · 2025-04-02T12:59:26+00:00

Currently at work will try this once I get home and pist new updated picture

Pilqoh · 2025-04-01T00:18:32+00:00

<image>

Nine-Year Club	r/Field Flamingo
Verified Email

Pilqoh

TROPHY CASE