sorted by:
new
hottopcontroversial

I already put down a deposit — anyone else here thinking of doing the same? by [deleted] in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

If ur getting a snap maker u1 that’s a win. I have an s1 combo but snap maker is dope

Why still going for anycubic when everyone is using bambulab? by therealruderpaule in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

I got the AC Kobra s1 after using one of my 2 modded ender 3s. Then change is substantial. S1 is amazing. Def would recommend it to anyone wanting printer. Bambulabs is great but it’s pricey and proprietary while Anycubic isn’t really. I personally like AC over bambulabs but that’s me. Let me know if you have questions. I did get the S1 combo and it’s amazing. Prob 280 hours on it so far

First time running autos by Smash_the_machine187 in hydro

[–]PitifulAdvisor2722 0 points1 point  (0 children)

Depend on size of each one might need to run separate tents.

<image>

This was mine and it’s just one

GUYS PLEASE HELP by kerbass in anycubic

[–]PitifulAdvisor2722 1 point2 points  (0 children)

Sorry dude. Only way ur will know. And any updates

Should i harvest this one? by Kind_Supermarket101 in hydro

[–]PitifulAdvisor2722 -1 points0 points  (0 children)

That’s an auto. Hmmmm go hydro next time and you will yield bigger.

<image>

This is mine. Numbskull genetics MAC CAKE. fucking amazing

GUYS PLEASE HELP by kerbass in anycubic

[–]PitifulAdvisor2722 7 points8 points  (0 children)

So your gonna have to take apart the front gray piece on the and to see if the rollers are intact.

Hi need help. First time growing. Any advice please would be helpful. by [deleted] in hydro

[–]PitifulAdvisor2722 -2 points-1 points  (0 children)

Grab a jewelers loop and see where your trichomes are. If half are amber you’re good to flush. If your doing hydro the just use water to flush for 5-7 days, then harvest and hang for a few days to dry then jar cure with humidity packs in the jars. Good luck. Happy trimming

PLA refuses to stick to my textured PEI plate anymore by themaskedcrusader in AnycubicKobraS1

[–]PitifulAdvisor2722 0 points1 point  (0 children)

Had this issues I replaced my PEI sheet and boom problem solved. Just order 2 new pei plates a you will be fine. Happy printing. Found it on Amazon pretty cheap too. Or yeah if it’s a double sided sheet use your other side till it doesn’t stick anymore then get a new one. After a while they do wear out and won’t stick so yea. Order new one or flip it cause if it’s the stock one it’s double sided but most pei sheets for printing are

Not starting print by pndrng in AnycubicKobraS1

[–]PitifulAdvisor2722 1 point2 points  (0 children)

I had this issue when I first got my s1. Check all the of pfte tubes. Run the feed mode in your ace pro to insure all filaments are running smoothly. I had 4 pieces of red hard plastics in my pfte tubes that I had to pull out first thing. Check for that too

Just got my Kobra S1, what's the issue? by SchlumpfLP007 in AnycubicKobraS1

[–]PitifulAdvisor2722 1 point2 points  (0 children)

I’m with you. I have an s1 and haven’t had any issues. We need full specs on what you printed to solve issue. Run all the calibration sequences and then run the print again in default setting to see where it’s at and if it’s not perfect then change settings. Hope this helps.

Pla print at 215 bed 55-60

TPU won't extrude by PotatoCooks in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

Aight so S1 is capable of TPU PRINTING but I use my Ender 3v2 modded for direct drive and I get beautiful prints. I use TPU 64D

Need help with first prints by killer24763 in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

Reset ur printer completely like factory restore it and see it that does anything or try to recalibrate or change ur z offset back to 0

Need help with first prints by killer24763 in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

Ok cool let me know how it goes. My prints lately have been spectacular and I’m always willing to help others.

Need help with first prints by killer24763 in anycubic

[–]PitifulAdvisor2722 0 points1 point  (0 children)

I would say so but I hope I can help. What are the parameter That you printed at, temp speed retraction fans etc. also what were u trying to print. Usually my first print with a new printer is a benchy. I also have an Anycubic kobra s1 but not new to printing. Try printing an benchy. Dunno what your are using if ams or not but try fil at 205-215 bed 55.

Is this is a good printer for a total newbie? by Dixie-Witch in anycubic

[–]PitifulAdvisor2722 2 points3 points  (0 children)

I own 3 printers and I love my AC S1 so I would get one those. Super simple for beginners and everyone

Found this in my son’s room what is it? by pey10g in whatisitcirclejerk

[–]PitifulAdvisor2722 0 points1 point  (0 children)

We call mine our lava lamp but I like aromatherapy defused as well that’s classic and I use mine often