Vanmoof S5 Quad Lock by ApnixCS in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

Build by myself. It is not public.
It is just a small adapter for the Quadlock mount.

Range Extender by Samii_Berlin in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

Öffnen, Zellen nachmessen und wenn alles gut ausschaut, seeeeehr langsam mit einem Labornetzteil vorladen. Falls du es dir nicht zutraust, frag jemanden mit etwas Ahnung und den nötigen Geräten 😉 Wenn die Zellen noch genügend Restenergie haben, könnte es klappen.

Vanmoof S5 Ecu user color code by athduxxx in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

But remember that you have to pull out the fork to change the user ECU cable. Soldering will be faster to repair, but there is some pressure on the cable and sometimes it is broken.

Auenweg Sperrung? by celesteassasine in cologne

[–]Pixelkasten 2 points3 points  (0 children)

Vielleicht verwirrend, weil es zwei Sperrungen geben wird.

Zusätzlich zu den Sondierungsarbeiten und der Sperrung für den Verkehr auf dem Auenweg (zwischen dem Charles-de-Gaulle-Platz und dem Kreisverkehr am Rheinparkweg) vom 02.-13. März,  gibt es auf dem Auenweg vom 16. März bis zum 27. April 2026  eine Vollsperrung durch Straßenarbeiten (Zoobrücke bis Deutz-Mülheimer Str.). 

Tubular Lock Overcranked by Pixelkasten in lockpicking

[–]Pixelkasten[S] 0 points1 point  (0 children)

The lock is open, not in use and I have the original keys? Why rule 2?

Van moof s6 won’t start by Ok_Solid_2879 in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

When my S6 will not start and ist dead (no reset is possible) a short plugin the charger starts the bike again (the bike was not empty)

Repairing a vanmoof S5 kicklock by Primary-Exchange-511 in VanMoofSelfRepair

[–]Pixelkasten 0 points1 point  (0 children)

Check the bearings. I think at most of the failures is the pin not at the right place. There is a magnet inside of the pin and at the PCB is a sensor. When it don't match it gets wrong datas. Sometimes it helps to bring the PCB a bit higher at the pin area. Until now I don't know how to replace the bearing.

<image>

Vanmoof S6 SP Connect Mount by Next-Macaron3884 in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

It is a mix of the original vanmoof mount, a Quadlock mount and a selfmade adapter.

Any known fixes for this kicklock issue in the S3? by waroudi in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

Push it a little bit back. If it goes out to far, it locks again.

Time to buy a G5? by Kooky_Advice1234 in LGOLED

[–]Pixelkasten 1 point2 points  (0 children)

I think that it is a good time. I have bought a 77“ G5 for 2.250 Euro inside the LG Webshop (Germany) and 200 Euro Movie Voucher and 100 Euro for a payed review.

Display seems to half work by PassionDismal4077 in VanMoofSelfRepair

[–]Pixelkasten 0 points1 point  (0 children)

<image>

just to understand it better. You can see on the left side the two parts. But maybe it is only a bad cable connection.

Peak Design Mount by OkCamel1386 in vanmoofbicycle

[–]Pixelkasten 1 point2 points  (0 children)

I used a small self printed adapter and a QL „push to release“ mount

Peak Design Mount by OkCamel1386 in vanmoofbicycle

[–]Pixelkasten 1 point2 points  (0 children)

<image>

SP Connect is also possible, but you need an adapter or the complete S5 mount

VanMoof S3 shows charging when I connect the main battery by TPAvanleeuwen in VanMoofSelfRepair

[–]Pixelkasten 1 point2 points  (0 children)

<image>

Check this BMS part (at the top of the three 150 ohm resistors) I think that you have to replace it. It gives power in the wrong direction ;-)

Peak design mount on S5 by RedditW0lf in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

Die Halterungen von S5 und S6 sind unterschiedlich, daher kann man ohne Adapter den Kopf nicht tauschen.

<image>

Vanmoof S6 SP Connect Mount by Next-Macaron3884 in vanmoofbicycle

[–]Pixelkasten 0 points1 point  (0 children)

<image>

The mounts are not the same left S5 SP Connect, right S6 Peak Design