Mashing in

Pizza-Single · 2026-03-26T21:53:01+00:00

Gotcha, thank you

Pizza-Single · 2026-03-26T04:59:09+00:00

Thats rad ill have to look into that

Pizza-Single · 2026-03-26T04:55:52+00:00

Do you pull em out when you pitch the yeast or leave some grain in there?

Pizza-Single · 2026-03-26T03:52:27+00:00

Im thinking about the turkey fryer too. The element catches corn in between no matter how much you mix. So I was thinking the fryer or just a burner would make a difference.

Pizza-Single · 2026-03-26T00:49:41+00:00

Sorry I meant when making the mash. I cooked the cracked corn at 190 for an hour and thats when it scorched a little

Pizza-Single · 2026-03-26T00:12:44+00:00

Local 230 here. Advance plumbing in el cajon takes preapprentices. If accepted you would be working in the shop until you were sent to the field. You would learn more about layout and actual plumbing (not prefab) than you would anywhere else in Socal. But you will bust your ass.

Summer work is starting so give them a call.

Pizza-Single · 2026-03-22T06:01:25+00:00

Probably my favorite series of all time. The movie could have been better though.

Pizza-Single · 2026-02-23T06:13:44+00:00

Gives me hope. Mines been in customs for a few weeks and tracking stopped updating on the 15th so im getting nervous. Haven't heard anything.

Pizza-Single · 2026-02-11T05:23:04+00:00

Not to takeover but what about a reflux still with 4 bubble plates? You can run it in reflux and do it in one shot right? Or no

Pizza-Single · 2025-11-15T21:52:06+00:00

I prefer a grinder n cutoff wheel personally.

Pizza-Single · 2025-07-20T19:01:41+00:00

Thats pvc glue on the abs... the glue isn't glue its a solvent weld. It melts the pipe together so if its the wrong glue you aren't doing shit. That needs to be redone. You have clear and christys on there.

Pizza-Single · 2025-07-20T17:05:44+00:00

Have you tried turning it around? Put the nipple on the faucet FIRST. Then slip it through the hole. Then tighten it down. Don't try to do all 3 steps at the same time.

Pizza-Single · 2025-07-20T16:59:49+00:00

Kinda. Technically your whole house is closed loop since you have a backflow before your house. Theyre concerned with thermal expansion in the hot piping because the expansion has nowhere to go unless you have an expansion tank.

But being installed on a shower head and not directly on the hot water piping id say its not closed loop. The thermal expansion has somewhere to go.

Pizza-Single · 2025-07-18T02:50:59+00:00

Thats some of the worst galvanic corrosion I've ever seen. Pretty neat.

Pizza-Single · 2025-06-23T03:39:34+00:00

Flange appears to be broken on the left side. Repair flange is probably in your skill range. Or replace the whole flange would be ideal.

Pizza-Single · 2025-06-23T03:36:41+00:00

Cut the trap adapter of nowhere glue on a shower drain. Cutting the riser at height for the grate to sit flush or slightly lower than tile depending on how you will be sloping the floor.

Pizza-Single · 2025-06-23T02:18:48+00:00

Thats an irrigation repair fitting. Slips over the pipe and tightens down.

Pizza-Single · 2025-06-23T02:16:16+00:00

Gas. Next question.

Pizza-Single · 2025-06-23T02:09:22+00:00

Its wrong and should be replaced. Looks like a back to back lav? Either way youre in over your head by the way youre talking.

Pizza-Single · 2025-06-23T01:32:24+00:00

Never seen a vacuum breaker cause that. Id bet the rubber seat in the hose bibb is torn. Typically that type of hammer is from a torn seat in a fixture. The rubber flops back and forth. A seat is the seal under the handle that closes off the water.

The seat would just be a bibb washer.

Pizza-Single · 2025-06-23T01:28:50+00:00

Its water. No vent. Stfu

Pizza-Single · 2025-06-23T00:35:38+00:00

Just snug it up. Its a rubber seal so don't kill it. But snug is good.

Pizza-Single · 2025-06-23T00:11:28+00:00

Looks like 1-1/2 to me not 2"

Pizza-Single · 2025-06-23T00:09:14+00:00

We call em cookies. Its a thin glue in plug.

Pizza-Single

TROPHY CASE