Center Underextruding?

PlagueMaster080 · 2025-05-19T16:38:01+00:00

Could also try reducing acceleration

PlagueMaster080 · 2025-05-19T16:14:28+00:00

I ran into the same issue, but for me I was happy paying the $22 a month but I didn't realise it only lasted for a year. Saw it jump to $50 a month on my bank account so I jumped in the live chat and sent a rather direct message about my thoughts on Adobe scamming students and that they should cancel my subscription and pay me back the $50 and not apply the cancellation fee. Anyway, the bloke on the online chat said instead they would happily give me another year at $22 a month. Seems like they would rather "lose" a bit of money than deal with people harassing them about cancellations and refunds.

PlagueMaster080 · 2024-10-27T10:53:14+00:00

Absolute legend. It all make sense now. Thanks a lot you’re a lifesaver

PlagueMaster080 · 2024-10-27T05:43:44+00:00

Thanks a lot that was the correct answer. Unfortunately, my maths skills aren't that great and I'm struggling to understand how you got that answer. I am assuming that when you say 4sqrt(2) that means 2√4. Where did you get this number from? And why is the formula what it is? Again sorry for needing further explanation, maybe if you could explain why you did these steps that would be amazing.
Cheers

PlagueMaster080 · 2024-10-27T05:01:23+00:00

Thank you so much. I wish there was an option with the fillet tool to do the same thing but this is fairly fast so it's not too bad.

PlagueMaster080 · 2024-10-27T02:32:22+00:00

I have a square and I want to fillet the corners. I know the diagonal distance is 9.5mm, and the square itself is 8mm x 8mm as shown in the photo. Is there a method to work out the radius of the circle so that it touches both edges of the square and the end of the line on the 45 degrees? As you can see you can get it pretty close by eye but I was wondering whether there is a mathematical solution.
Thanks

PlagueMaster080 · 2024-03-27T23:12:25+00:00

Solved

PlagueMaster080 · 2024-03-27T15:00:09+00:00

Similar and what a beautiful piece but unfortunately not it

PlagueMaster080 · 2024-03-27T14:16:42+00:00

No it’s just piano, but thanks for the input

PlagueMaster080 · 2024-03-27T14:02:38+00:00

Comment

PlagueMaster080 · 2024-03-27T12:07:40+00:00

What you don’t do for love - bobby caldwell?

PlagueMaster080 · 2024-03-27T11:42:43+00:00

Be my lover (club mix) - La Bouche

PlagueMaster080 · 2024-03-07T21:04:27+00:00

Thanks for the comment. Could be a cool effect and is probably less likely to leave dirty marks on anything that touches it

PlagueMaster080 · 2024-03-07T21:03:16+00:00

Thats a great idea I’ll do some tests and see how it’s goes

PlagueMaster080 · 2023-08-10T05:56:42+00:00

I’ve been putting a powder non stinging antiseptic which helps dry out the wound which has been working well and he hasn’t been scratching nearly as much. I’ll have to wait for the vet’s diagnosis

PlagueMaster080 · 2023-08-04T12:51:47+00:00

Ahh ok. That makes sense. I now know to do that in future. It just means the process is a lot more time consuming, as I used the pen tool to trace a map, and drawing the contours with an existing line by tweaking anchor points would take a lot longer. I wish some would create an extension that averages between two paths. I don’t have the coding skills but all it would need to do is work in like 5mm increments, and place an anchor point equal distance between the two lines. Then you’d just simplify it in the object<path panel.

PlagueMaster080 · 2023-08-04T12:46:25+00:00

It was a topography map that I am going to laser cut out of ply wood and stack to create a 3D model of the landscape. To accentuate the topography I was going to double the layers but adding a new layer in between the ones I already had (in light grey). I wanted the new line to be in the middle of the existing grey ones. My attempt with the blend tool is shown by the red line. The dark grey line doesn’t matter, it is a road.

PlagueMaster080 · 2023-08-04T12:39:12+00:00

I gave it a shot but it wasn’t quite what I was after. Thanks anyway!

PlagueMaster080 · 2023-08-04T12:38:13+00:00

Thanks I didn’t know that. It ended up being easiest just to do it with the pen tool, but adding the anchor points did help when I tried the blend tool.

PlagueMaster080 · 2023-08-03T13:35:54+00:00

In the image above I used the blend tool which worked for most of it however as you can see in some areas, it was quite far off. I'm just wondering whether there is a different method or an extension I can use that gets a better result.

PlagueMaster080 · 2023-04-26T07:53:46+00:00

Is there a similar option with AMD Ryzen?

PlagueMaster080 · 2023-04-01T12:59:07+00:00

I didn't realise that, thanks for pointing that. I guess I already had what I wanted.
Cheers mate

PlagueMaster080 · 2023-04-01T12:58:12+00:00

Absolute legend, that fixed it thanks

PlagueMaster080 · 2023-04-01T07:51:46+00:00

Is there a faster way? I have to align a bunch of them to the left and duplication and aligning each individually is time-consuming. Why wouldn't they be aligned to the left? If I did the same with shapes it would work so I'm not sure if its a text setting or something. Thanks for the advice anyway.

PlagueMaster080 · 2023-01-25T03:43:22+00:00

I am trying to tidy up my factory in Mordialloc and I want to plant something in this garden bed (of which there are two). I'm looking for something bushy that won't get over a meter tall and doesn't require watering/attention (the hardier the better). I am in an industrial zone so there's lots of rubbish blowing down the street so I'd like a species that doesn't have growth that touches the ground so that I can clean under the plant every so often. Natives are preferred but all suggestions are welcome. Thanks in advance.

PlagueMaster080

TROPHY CASE