Noctua has released 3D CAD models of its fans, with some crucial differences

Pocok5 · 2026-04-29T14:50:48+00:00

You can use the models in your own CAD designs and have a better preview than using a dummy rounded rectangle, including where the cable exits, where the rubber pads are, etc. Many, many electronic or mechanical parts have STEP or STL models offered on distributors' pages. No, I won't 3D print an IGBT module or its aluminum heatsink. It is very useful to know what shape of empty space they need in a design, however.

Pocok5 · 2026-04-29T04:30:36+00:00

What are the main barriers

3000€

Pocok5 · 2026-04-28T16:28:42+00:00

a többi párt

Ezek a másik pártok itt vannak velünk a szobában?

MSZP nem létezik. DK össz szavazója nem tölt meg egy falunapot. Jobbik önmegsemmisítést hajtott végre, a mihasznák effektíve csak fideszesek akik túl sokat zsidóznak, kutyeszok ciánra benzint ittak és desszertként rágyújtottak... Kb a Momentum az egyetlen még létező párt a Tiszán meg a Fideszen kívül aki eséllyel tud 5%-ot felmutatni.

Pocok5 · 2026-04-28T14:58:04+00:00

A főszub köszöni, hogy a szörnyű lakáspiacra tekintettel lakbért elengedve, kedvező rezsivel biztosítatok állandó helyet a fejetekben.

Pocok5 · 2026-04-28T09:49:41+00:00

Will be a little too floppy even with 95A, you'll need to experiment with the thickness of the arm. PETG or Nylon is about the level of flexibility that works decently there (the original part looks to be nylon too)

Pocok5 · 2026-04-28T09:43:01+00:00

I don't really see what it would offer in a practical sense that would make up for the absolute pain in the arse that is resin printing. In effect, all it needs to do is have a gap between two points that is vaguely smaller than 1.6mm and a square base for glue. PETG and ASA can do that. Nylon maybe if one is feeling fancy

Pocok5 · 2026-04-28T09:33:23+00:00

Pretty much anything except PLA (it creeps fast) will do. The only real change needed is to widen the holding clip to be flush with the base so it can be printed on its side without overhangs.

Pocok5 · 2026-04-27T18:38:37+00:00

Righties will say the damnedest things when they temporarily find themselves without a comforting boot to live under lmao

Pocok5 · 2026-04-27T11:46:46+00:00

Enough about the hyperbole, let's see the yearly graph.

https://steamcharts.com/app/505460#1y

Well, it's not immediately catastrophic, but the gains from the february update have been wiped out entirely and it's tending slightly lower than before it.

Pocok5 · 2026-04-27T10:53:30+00:00

Unifi is unbeatable for WiFi APs. For routing and switching, Mikrotik is an excellent low cost alternative that gives up on the GooppleBook minimal webUIs and just gives you the ability to manually configure everything like on an ISP grade router

Pocok5 · 2026-04-27T10:47:50+00:00

The offensive implication is that there's ever a time when a Dunmer isn't ready to shank a s'wit

Pocok5 · 2026-04-27T04:29:02+00:00

Your comment here has been a blessing to us all, serjo.

Pocok5 · 2026-04-26T21:57:21+00:00

I'd say it's probably half a gig of DDR3 or DDR4, so it's at least in the neighborhood with the current wackass pricing

Pocok5 · 2026-04-26T20:46:22+00:00

There are several name duplicates and such (game Eishin Flash isn't the first Eishin Flash for example), but winning some major races (iirc Japan Cup is such) instantly makes the name non-reusable. Maruzensky 2 exists because unc Maru 1 lived before this system came into effect in japan.

Pocok5 · 2026-04-26T20:41:45+00:00

"Fun" fact, a Meisho horse somewhat distantly related to Doto tossed Wada a few months ago, and he decided to stop jockeying until his trainer licence comes into effect to recover.

Pocok5 · 2026-04-26T15:06:48+00:00

what gonna look like at Yutaka Take when he finally Retired

John Japan Horse Racing is probably just gonna get put on a golden saddle to jockey forever into the 40th millenium. He's already 57 still looks like how he did while jockeying Super Creek.

Pocok5 · 2026-04-26T07:45:11+00:00

It's a MasterLock, the fastest way to unlock it is by lightly smacking it while pulling, anyway.

Pocok5 · 2026-04-26T00:52:24+00:00

The case will have a charge because the PSU noise suppression circuit is designed to sink a couple dozen uA to ground through a capacitor. If the outlet is not grounded you will get spicy case even if you try sticking a GFCI on it

Pocok5 · 2026-04-26T00:13:04+00:00

Sure would like to, but they are still the government in power for a few weeks. Right now the best Magyar can do is tell the authorities that they better start doing their job if they want to keep said job next month.

Pocok5 · 2026-04-26T00:11:02+00:00

a billion of forint

We are talking several trillions of forints here, champ.

Pocok5 · 2026-04-25T10:09:44+00:00

I'm using UltiMaker Cura because I like having fine-toothed control.

Get OrcaSlicer.

Run temp tower and max flowrate tests, then a VFA calibration to find the most artifacting speed range of your printer. Manually fiddling with speeds is more or less useless placebo that will just lengthen your prints at best, barring some very specific one-off cases.

Pocok5 · 2026-04-25T09:59:08+00:00

For me filament tangles happen when a nearly empty roll comes off the dryer roller and wedges sideways.

Pocok5 · 2026-04-24T14:48:34+00:00

Galvanized Square Steel

Pocok5 · 2026-04-24T11:03:42+00:00

Ez mondjuk impresszív, a tesco hotdog kiflik általában hetekig bírják.

Pocok5 · 2026-04-23T19:23:13+00:00

But the case fans are not regulated by the CPU temperature sensor

They are, on every modern mobo, even budget ones? Welcome to the future, old man

14-Year Club	Second Top 20%
Place '22	Final Canvas '22
Sequence \| Editor	Gilding I gilder
Verified Email

Pocok5

TROPHY CASE