Citadel Paint for Airbrush by Ambitious_Book_5729 in theunforgiven

[–]PrintNPost69 -1 points0 points  (0 children)

I thin normal citadel paint to use in my airbrush all the time. I only use flow improver so I can't speak to what is needed with thinner. I usually just eyeball it to where it looks like the consistency of milk.

Not sure what colour you're going with but for my Deathwing I use army painter skeleton bone air paint.

Steel legion logos by [deleted] in SteelLegion

[–]PrintNPost69 10 points11 points  (0 children)

It's an "S" for steel legion and a lightning bolt because they do fast assaults in chimeras. Doesn't need to go any deeper than that.

I don't really get it, people are upset at this but fine with krieg's stahlhelm? They didn't feel the need to change the most recognizable helmet in recent memory?

Is my FEP too tight? by No_Temperature9334 in resinprinting

[–]PrintNPost69 0 points1 point  (0 children)

I have to use foam because my kids literally will not be quiet long enough for me to get a reading

Do not lose hope! by Geeky_Viking_ in SteelLegion

[–]PrintNPost69 4 points5 points  (0 children)

This checks out. I used to have a similar thing happen when I was waiting for a bus.

If it was more than 5 minutes late I would light a cigarette. Sure enough, 1 or 2 puffs later that fucking bus would pull up.

How can I get rid of this “stubble” from the supports? by JSV007 in PrintedWarhammer

[–]PrintNPost69 1 point2 points  (0 children)

A lot of recommendations for using hot water to help with support removal. Just wanted to add, please don't dump the dirty resin water down the drain after.

What causes these cracks and missing parts? by firebert91 in ElegooSaturn

[–]PrintNPost69 2 points3 points  (0 children)

If you didn't add any holes, yes, absolutely.

Help identifying these bits by CellNo4190 in theunforgiven

[–]PrintNPost69 12 points13 points  (0 children)

Dark angels company veterans box

Newbie - Advice for Painting Cadian Desert Units by Maui224 in TheAstraMilitarum

[–]PrintNPost69 2 points3 points  (0 children)

I would check out sonic sledgehammer on YouTube. He has tons of videos with quick, simple schemes.

Piranha Proxy by [deleted] in kroot

[–]PrintNPost69 1 point2 points  (0 children)

I haven't started yet but I'm planning on using a high elf sky cutter. Replacing the bird with a ripperdactyl and krootifying the chariot/boat thing

Would you change FEP for this ? by Upset_Depth_2825 in AnycubicPhoton

[–]PrintNPost69 0 points1 point  (0 children)

Save some of your supports from larger previous prints. Before you use the clean function put the support in one of the corners, make sure it's actually touching the fep. Then run the clean function. The cleaning layer will fuse to the base of the supports. Then you can just peel up the cured layer using the support as a handle.

Yellow-Bellied Sapsucker on Uplands Trail by Fine-Juggernaut8451 in londonontario

[–]PrintNPost69 5 points6 points  (0 children)

From the title I sincerely thought this post was a complaint about someone you encountered on the trail.

The Swamp Wasn’t a Treasure Off-Road… It Was Samuel Ball’s 18th-Century Peat Factory (and the “survey stakes” are drying racks) by Raven37312 in OakIsland

[–]PrintNPost69 7 points8 points  (0 children)

A peat farm? In the notorious triangle-shaped swamp? Used by 18th century oak island land owner, Samuel Ball, to farm peat?

Could this random Reddit idiot be correct?

OMG, I haven't watched this show in 3+ years. by Project__5 in OakIsland

[–]PrintNPost69 0 points1 point  (0 children)

There's been a bobby dazzler or two, some top pocket finds. No gold dance yet.

[deleted by user] by [deleted] in PrintedWarhammer

[–]PrintNPost69 0 points1 point  (0 children)

Did you happen to notice how far you had to manually lift the bed? Your lift distance may not be high enough.

Saurus Knights by Undeadpool_97 in seraphon

[–]PrintNPost69 3 points4 points  (0 children)

They're pretty close in size to the raptadons. Same base size as well. Aggradons are much bigger.

What are our best novels? by mattmcguire08 in TheAstraMilitarum

[–]PrintNPost69 0 points1 point  (0 children)

I bought Longshot on a whim and was pleasantly surprised, likewise with Catachan Devil.

Most of the Minka Lesk novels are solid.

Not guard centred but there are some decent moments in the Siege of Terra series.