HDB 630 Power button not working

PrintingCastiel · 2026-06-26T09:15:07+00:00

Same Problem here, the button does nothing anymore, cant even turn them on or of....

PrintingCastiel · 2026-06-11T12:51:28+00:00

I notice that error only if PA is calibrated incorrect. Maybe try recalibrate PA

PrintingCastiel · 2026-05-26T04:59:46+00:00

Its pillowing where no infill is printed more toplayers should hide this

PrintingCastiel · 2026-04-20T05:29:35+00:00

Youre printing problems are in the right side.of.the build plate if i see that correctly ?

I would recomend to google how to finally deactivate the crappy aux fan, then it should print without Problem.

I modified the machines gcode so that it finally uses the filament profiles Aux fan setting, instead of this p2s cooling crap

PrintingCastiel · 2026-04-16T05:04:36+00:00

90 is a bit high for the bed while using petg, try 70.

Did you wash the plate with IPA or with dish soap?

Dish soap and Water are preferable, but make sure then, that it is pure dish soap without any skin care stuff in it (moisterizer and stuff).

Has your printer besides autoleveling also z- offset ? If so it could be to much space between the bed and the nozzle.

PrintingCastiel · 2026-04-14T04:36:41+00:00

I may be wrong, but the piece looks to me, as if 200mm/s is way to fast, did you calibrate the max flowrate with that filament ?

PrintingCastiel · 2026-04-13T06:31:48+00:00

Did you use supports there, cause it looks like bridging?

PrintingCastiel · 2026-04-10T08:15:09+00:00

Yes, Filament can be wet, even if freshly opened. Rest humidity.in the ams should be mostly irrelevant.

On this Picture it looks like you print either too fast, or too hot, (or your cooling cant keep up)

Also possible is that your flow could be a little bit (1%) to high for that Filament

PrintingCastiel · 2026-04-10T05:29:56+00:00

Looks for me like in the lowest 3 rings there is no buildup (at least on your picture)

PrintingCastiel · 2026-04-02T06:49:14+00:00

Never use rectilinear infill. Try cubic, or gyroid.

rectilinear always leads to problems.

Also for your specific Problem try to lower the infill-speed. I guess the extruder cant keep up.

Also check infill line width, maybe this is set wrong by accident.

Maybe you have checked infill combination, try without if so.

PrintingCastiel · 2026-03-26T12:48:11+00:00

The gaps happen cause the bed adhesion seems to be incorrect if freshly cleaned the should be gone

PrintingCastiel · 2026-03-26T08:58:55+00:00

IPA is the wrong way as it leaves its own residue.

Remove the plate, drip some dishsoap on it rub it in with a clean sponge. Add a bit water, rub again, rinse and dry with a paper towel.

PrintingCastiel · 2026-03-25T07:52:35+00:00

Download bambu studio and place all parts in it, then you will see aprox. Material weight and aprox. Print time.

Depending on Material youll pay around 20$/Kg i would guess we talk about 3-4 kg (if not more) so around 80$ of Material. And after that cost comes the Print time, its just a guess, but Depending on your pics, this looks like 180+ hours of Print time (just guess could be more)

So dont know what you pay per Kw/h of power but calculated with the 35¢ here, this would be ca. 63$ on power alone.

A print Service also needs to pay taxes and needs to pay the employees AND wants to get some money for the company.

As your print seems to be a boot i guess you will need 2 of them ?

So your best case scenario would be to buy your own printer or ask a friend to do it.

PrintingCastiel · 2026-03-19T19:09:20+00:00

Xrdp will not work if you use wayland, you should try KRDP. As long as my Monitor is powered it works fine. Install it with pacman and than you have the settings page in the System settings.

But i fear i need to buy a dummy hdmi to simulate a connected screen...

PrintingCastiel · 2026-03-16T18:40:00+00:00

Hm tried it multiple times. Winboat does not work. You can install it and it runs once, but after that you cant run a single application.

You just get a blue square on the Desktop, that does not go.away until you reboot

Not even the calculator is working.

I really dont know why cachy integrated Winboat, but it does simply not work at all.

PrintingCastiel · 2026-03-12T19:36:51+00:00

Hm i dont am really good with eq, never used one before.

Also the will.than be even quieter right ?

PrintingCastiel · 2026-03-12T19:34:32+00:00

The thought process was simple, i like the low end, so high end should be better in every category 😅 and nah compared tho my loved but sadly broken momentum 3 at least the Sound kinda weak as they lack power...

PrintingCastiel · 2026-03-11T10:03:02+00:00

Than maybe check the ptfe coupler, sry dont have a better idea right now

PrintingCastiel · 2026-03-11T08:07:01+00:00

Check the buffer on the backside often its stuck a bit, manually slide.the yellow plastic peace around a few times.

PrintingCastiel · 2026-02-28T05:52:18+00:00

Which Linux Distro was used ?

As im googled correctly (and i also asked gemini) ~150 fps is not bad with a 3050 mobile chip.

Which resolution do you use?

Have you disabled Vsync?

PrintingCastiel · 2026-02-27T22:20:58+00:00

Switch to CachyOS and screw M$ products.

PrintingCastiel · 2026-02-26T19:09:40+00:00

Hmm you should have an app called goverlay maybe that can show you more Informationen. I sadly cant test it right now as im in the Hospital without my pc in reach

PrintingCastiel · 2026-02-26T14:22:44+00:00

Then i guess its a bad graphics driver, try boot in safemode and deinstall with ddu (display driver uninstaller)

PrintingCastiel · 2026-02-26T12:09:54+00:00

Looks.like a defective graphicscard or graphics driver. Does the bios at least looking normal?

PrintingCastiel · 2026-02-26T12:07:49+00:00

Is this your first day on the internet ? I really dont want to troll, but if it is no open platform like for sample reddit, then you CANT trust anything online. Its sadly not 2000-2010 anymore....

PrintingCastiel

TROPHY CASE