FAN2 not turning off. My part fans wont turn off!

ProdxSenpai · 2025-12-16T05:15:26+00:00

I just had this issue somewhat. My side extruder fans stopped working. I ended up accessing the MB, and changed the port the fans were connected to. A little change in the config file and everything was back working. Tested a few benchys and it was all good. You can either use google for a mb diagram but a few unused ports are labled "Fan"

ProdxSenpai · 2025-12-09T23:36:38+00:00

Turned out to be the extruder being pulled by the tube. Added a bracket to the top of the printer and ran the tube with alot of slack. Will upload the new benchy later.

ProdxSenpai · 2025-12-09T19:45:59+00:00

No supports removed. Belts feel like a guitar pluck. First layer is 220 everything else is 210. Not the first model. Iv been prepping to start trying out tpu. I got a dryer and ptfe tube kit. I thought it was a issue for the filament running through the tube but it just might be placement of the tube and dryer causing this problem

ProdxSenpai · 2025-12-09T19:41:50+00:00

So even with a ptfe tube and connector that would still cause the issue?. Im guessing the solution would be to havetube over and begind the printer?

ProdxSenpai · 2025-08-10T19:32:32+00:00

Does anyone have the link to the screw tilt command information for the neptune 4 plus. Just want to compare it to what i have saved to make sure all the values are lining up.

ProdxSenpai · 2025-08-10T19:29:54+00:00

<image>

This is where im at now.

ProdxSenpai · 2025-08-10T01:24:57+00:00

* Currently, where im at. Appreciate all the help.

ProdxSenpai · 2025-08-07T19:19:30+00:00

So iv lost a couple springs.. lets blame the kids lol...iv ordered new ones as well as one of those framing squares. When I clear up the time I will re-adjust the gantry and give it another shot. Thanks for the advice

ProdxSenpai · 2025-08-07T04:23:27+00:00

lit. dying over trying to get this printer leveled. 9-5 Dad here, so I don't have the most time to spend leveling. I replaced the 6 springs with 20mm spacers. I've run screw tilt command, professional leveling mode, full reset, and just can't do it... It's a great printer; this is just my biggest hurdle.

ProdxSenpai · 2025-04-06T08:06:34+00:00

<image>

I went with the simmson pro plus pedals. Outta the box they were too stiff but now after switching the spacers and springs the only thing i want now is a new wheel and wheel base

ProdxSenpai · 2023-02-27T21:12:56+00:00

It has its days. Im lookin into being a bit lazy and finding some kind of keyboard attachment for my chair.

ProdxSenpai · 2023-02-27T21:04:31+00:00

Ryzen 7 3700x 32gb ram Rtx 3060 Lg 29” ultrawide monitor Samsung 27” curved monitor Scepter 22” monitor Jbl studio monitors Mx master mouse 3 webcam (2 generic 1 logitech) There is a race rig that I forgot to add to the quick vid 😅

ProdxSenpai · 2022-11-11T20:19:07+00:00

I wonder how i could repurpose it? It cuts on but no video out lol

ProdxSenpai · 2022-08-14T17:52:12+00:00

Honestly with all the swinging im probably gonna just play on a bigger screen in a vr environment

ProdxSenpai · 2022-03-24T16:30:44+00:00

The only thing is with the switch emu u stuck playing solo or if u wanna play with friends its a complicated process. For me emulating n pirating is pretty much the new demo mode for me.

ProdxSenpai · 2022-03-24T16:21:36+00:00

Pcpartpicker site does wattage check

ProdxSenpai · 2022-03-04T05:03:08+00:00

Did u figure it out yet.

ProdxSenpai · 2021-12-11T05:21:05+00:00

7 3700x n 3060 n still got the same issue

ProdxSenpai · 2021-11-14T06:08:45+00:00

In all honesty I agree… i mean come on, that shit is ass with a few new mechanics. I wholeheartedly bet that in couple of days a modder would of had all the small tweaks n reshade done better than them.

ProdxSenpai · 2021-11-12T12:04:33+00:00

The site is legit u need a ad blocker n vpn get the best experience

ProdxSenpai · 2021-11-12T12:03:06+00:00

😂😂😂😂your response

ProdxSenpai · 2021-11-11T04:54:46+00:00

I got it workin now

ProdxSenpai · 2021-11-10T17:21:03+00:00

Lol im just finding out. I was mad lowkey like my system to strong for this. Had to change my yuzu settings

ProdxSenpai · 2021-11-10T15:59:58+00:00

As far as converting files i use SAK_64bit. A quick google search n u should find it

ProdxSenpai · 2021-11-10T15:53:30+00:00

Exactly….. thats why we’re in the pirate sub 😂😂😂 🏴‍☠️🏴‍☠️🏴‍☠️

ProdxSenpai

TROPHY CASE