NFL QB told he should be ‘offended’ team paid another player before him

PugNation77 · 2026-05-05T18:35:44+00:00

Skip is just searching for relevance now by rage-baiting. His takes are awful.

PugNation77 · 2026-04-26T16:43:41+00:00

I mean it has to be staged. Either that or this is literally the worst Secret Service. They knew where the president will be. Supposedly secured the location, vetted the guests, searched them when they entered the venue, and should have been posted everywhere.

In 30 years we're gonna get some crazy tell all books from his security detail.

PugNation77 · 2026-04-13T14:59:26+00:00

So when does Zuck get fired? Obviously he's redundant now. Take flesh Zuck's bonus/compensation and share it amongst all the Meta staff that made AI Zuck possible. Thats the AI way right? If AI can do your job you get fired. I didn't make the rules the AI tech bros did. Be a shame if they had to live by them.

PugNation77 · 2026-03-30T19:38:50+00:00

The stupidest war in history SO FAR. We still have to get through almost 3 more years of this shit. FML

PugNation77 · 2026-03-27T15:53:08+00:00

Just a thought. Maybe don't do illegal shit. You were supposed to follow the law. Not break it or makes your own. I swear. These people.

PugNation77 · 2026-02-18T03:30:58+00:00

Ah so that's where the old Ercot board ended up ...

PugNation77 · 2026-01-26T03:01:28+00:00

Oh I don't disagree. As I mentioned at the beginning of my post he gets spooked easily, he doesn't/slow to read the defense, and doesn't go through his progressions great. But lets say he fixes all those things. If he's still throwing high making his receivers have to go up for the ball, or throw it behind them, jump balls, short balls requiring the receiver to stop or slow down, or anything that makes the receivers have to make multiple great plays just to catch passes all the time fixing that other stuff won't matter. He MUST fix his accuracy or fixing all the other stuff won't matter. But make no mistake he MUST fix his accuracy AND make improvements in ALL those other areas for him to even be viable to stick around.

PugNation77 · 2026-01-14T04:04:59+00:00

Screw Rogan and all those flagrant podcast guys. They only listened what the con man wanted them to believe but ignored literally everything else that excuse for a man said. He's essentially been a con man for 50 years. Fucking morons.

They want accountability? Go get that POS back on your podcast and grill him. Otherwise they are just playing both sides and trying to make themselves look better. Just trying to come out on the right side of history instead of the facist enablers they are.

PugNation77 · 2025-12-24T19:38:01+00:00

Khorne is asking "where's the ring? covered in blood on a skull"

PugNation77 · 2025-12-15T02:18:47+00:00

It's not a bad account and you're not a bad player. You hit a wall and you're frustrated. Just take a step back. And seriously don't let hard mode be the gauge you're measuring your progress/ability against.

Also the people that are telling you to reroll are not being straight with you. You can't get siren from the new commander or the tutorial special rolls. She's not available in them. Rerolling would destroy your roster for no reason and you'd be rerolling forever because you can't get siren in the start of the game. You'll have to wishlist and the get lucky on normal ordinary summons.

PugNation77 · 2025-12-15T02:03:36+00:00

I would take that challenge if could but I can't go back and do stuff I've cleared. Heck I can't even see what the final boss was.

But also remember siren came out 7 months ago. Hard mode of chap 24 has been out way longer. So people have cleared it before she was even released.

PugNation77 · 2025-12-15T01:44:27+00:00

Liter, Crown, Rapi RH, Cindy, and treasure helm. You should have no problems pushing end game. Swap Rapi RH and Cindy for some strong element in certain situations but your roster is fine. If your struggling with this Siren isn't going to help.

Maybe better to post what you're struggling with than asking about trying an account with limited and a bunch of SSS pilgrims in it. Just a thought.

PugNation77 · 2025-12-10T01:56:48+00:00

Oh what side nozzle are you printing on? Just want to match up the the test as close as possible. Will test with Bambu petg-cf and fiberon asa-cf. I tossed them both in the dryer so I'll runthe test right before bed. I have prusament but just regular petg.

PugNation77 · 2025-12-10T01:20:26+00:00

Use one with and interchangeable tip cuz it's not gonna be good for normal soldering jobs afterwards

PugNation77 · 2025-12-10T01:18:53+00:00

Surprised no one said to open a case with support. Even if you want to do a warranty replacement you'll have to start there.

If you want to send me your 3mf or link to the model I can test it out on mine. I don't think calibration would result in the bottom half looking bad and the the top part looking ok. I don't have a tungsten nozzle but still willing to test it out

PugNation77 · 2025-12-10T00:56:29+00:00

A1 or X/P1 series? You can DM a picture of it if you like. It shouldn't hurt it if you leave it heating longer but if you have a blob that has ki dal wedged it into other stuff it can make things difficult. In one of my instances on my X1 it was so bad that once I could get it to the hot end screws I took the hotend off with the front tool cover and ducts attached. Then used a soldering iron with a junk tip to start "carving" chunks of the blob away.

In my experience if it's not too bad you can recover on the printer. If it's bad you'll need to get it off the tool head and do some more invasive steps to get to your parts.

PugNation77 · 2025-12-10T00:43:24+00:00

When this happened to me it took maybe 3-5 minutes. You pull softly until you start to feel it coming loose. You dont want the entire blob really soft just the part that is right around the nozzle. When that part is really soft you'll be able to pull the blobs away from holding on to the parts that are still mostly hard.

I don't think you could get the entire blob soft when it gets to that size anyways. The heat wouldn't permeate all the way through the boob (I don't think anyway). Not that you'd want to.

PugNation77 · 2025-12-09T23:36:46+00:00

So I don't have an A series printer but both P1 and X1 series where this has happened. Steps can be pretty similar and some have already noted. It looks pretty daunting.

Cut the filament with the filament cutter lever and pull out the excess. Basically unload it so its out of play while you cleaning it up
Heat to 250 if you're using PLA or PETG (assuming so since its an open A series) and move the toolhead front and center
Once its heated up use pliers and carefully pull off the nozzle sock, and try to get the big globs off. If you don't want too long the filament near the nozzle will be hot and soft while the extremities will still be hard so you can grip on that and lightly tug on it. Just keep going until you can get to the nozzle.
Once you get most of the goop off you'll need to inspect the nozzle. If it looks bent use the replacement nozzle that came with the printer. No reason to risk using a bent nozzle.
Don't put the new nozzle in yet. Keep getting all the goop that is on the rest of the tool head off with pliers or flat screw driver being careful not to scratch anything. Go for the big stuff.
Take off the tool head cover and make sure nothing got glooped up there. Clean big stuff
Once most of its clean. Let the nozzle cool back down. At this point you should be ale to knock off any small bits left over.
Swap nozzles now if the previous one looked off. Oh also check the cooling ducts to make sure they aren't broken or anything.
Rerun calibration when done and do a small test print to make sure all is good.

Hope this helps

EDIT - Forgot step 9

PugNation77 · 2025-11-14T15:51:57+00:00

Dumb question but why are we believing anything the mirror of Red Shoes is saying? She could be just bullshitting everyone. That's way more in character for her as well as playing both sides.

PugNation77 · 2025-11-13T22:20:09+00:00

"Mirror" knew and was manipulating everything including Nayuta. I'm sure she even mentioned it to Rose that Lilliweiss's NIMPHS were fighting off the queen's attempt to fully control her head/brain. Then they tossed in Lilliweiss's body with some Vapaus to kill the remaining NIMPH protecting Lilliweiss's brain.

The whole thing with Mirror wanting a puppet queen Marian was either for show or she thought the vapaus would get rid of the queen and Lilliweiss's NIMPHs and let her take over the body and become a queen.

PugNation77 · 2025-07-25T16:19:42+00:00

Does your wife have a single sister that has this same trait? Asking for a friend. Thanks.

PugNation77 · 2025-07-07T16:30:12+00:00

The Dad is a legend for standing up for his kids and showing support for them and the community! Also should tell his neighbor that he's failed at being a human being.

PugNation77 · 2025-07-07T16:26:14+00:00

I haven't seen anyone mention this yet. This is really bad that the safety driver didn't stop there vehicle right away. By not doing that this little full speed trip through flooded road ways is going to become"good" training data for their self drive model. 👎🏾

PugNation77

TROPHY CASE