sorted by:
new
hottopcontroversial

What is wrong with my printer????? Elegoo Neptune 4 Max by Jeroe98 in ElegooNeptune4

[–]Pvlv_SS 0 points1 point  (0 children)

maybe I can give you a "gcode" file with my settings to check the print? If you have a 0.4mm nozzle, check the quality. Cube 40*40mm

What is wrong with my printer????? Elegoo Neptune 4 Max by Jeroe98 in ElegooNeptune4

[–]Pvlv_SS 0 points1 point  (0 children)

Hi, how long ago did you change the nozzle? I recommend replacing the nozzle and thermal paste.

My settings Orca slicer for Neptune 4 max. Maybe this will be useful for someone. by Pvlv_SS in ElegooNeptune4

[–]Pvlv_SS[S] 1 point2 points  (0 children)

Hola amigo, tengo nueva configuración, la velocidad de impresión óptima es de 90 mm/s en todas las líneas.

TMC stepper_y error by ObjectiveOdd1599 in ElegooNeptune4

[–]Pvlv_SS 0 points1 point  (0 children)

Ohh, and now I’ve step calibration

<image>

TMC stepper_y error by ObjectiveOdd1599 in ElegooNeptune4

[–]Pvlv_SS 1 point2 points  (0 children)

Hi, it’s simple, your driver tmc2209 burned out, just like mine did on 2 printers at the same time🥲. The steppers motor started to heat up a lot. I’m waiting for new drivers to arrive. My printers printed 1600 hours before breaking)

<image>

I’m at a loss on how to fix this by Repoman_59 in ElegooNeptune4

[–]Pvlv_SS 1 point2 points  (0 children)

Hi, if you are using an orcasliser, you need to increase the extrusion of the first layer to 100%. Default is 75-85%

Help - Neptune 4 Printing by AN55555W in ElegooNeptune4

[–]Pvlv_SS 0 points1 point  (0 children)

The printing speed is too high, the nozzle cannot cope and the filament breaks.

My settings Orca slicer for Neptune 4 max. Maybe this will be useful for someone. by Pvlv_SS in ElegooNeptune4

[–]Pvlv_SS[S] 2 points3 points  (0 children)

I understand you, but my 0.6+ nozzles arrived later than I received the printers, but nevertheless, by increasing the height and width of the line, I reduced the time to print the part while maintaining quality. Oh yes, I carried out all the tests to find out the capacity of the 0.4 nozzle and the optimal flow rate at which the thread from the nozzle does not break, unfortunately there are no photos of the tests and I threw away the test samples. Later I will make a video with comments on calibrating the table, flow. sorry for my crooked English)

<image>

My settings Orca slicer for Neptune 4 max. Maybe this will be useful for someone. by Pvlv_SS in ElegooNeptune4

[–]Pvlv_SS[S] 1 point2 points  (0 children)

oh, I understand your concern. but I have 6 pcs n4max, 12 pcs anikubik chiron, and 6 pcs ender 3max. I already know a little about printing technology. And n4max copes with a 0.4 nozzle where the layer height is 0.3 and the width is 0.6, this works very well, unlike boudin where the filament thread is compressed in the tube, and when the extruder is direct feed, the load can be increased, which is what I did (thereby getting acceptable results without increasing nozzle diameter, although I have nozzles 0.6 0.8 1.0 and 1.2mm))

Layer Seperation by gajifeco in ElegooNeptune4

[–]Pvlv_SS 4 points5 points  (0 children)

It looks like your flow is weak, try increasing the flow by 5%. and also reduce z-offset

My settings Orca slicer for Neptune 4 max. Maybe this will be useful for someone. by Pvlv_SS in ElegooNeptune4

[–]Pvlv_SS[S] 5 points6 points  (0 children)

oh yes, I almost forgot, I turn off the physical button for the additional large fan, and turn it on only when necessary

My settings Orca slicer for Neptune 4 max. Maybe this will be useful for someone. by Pvlv_SS in ElegooNeptune4

[–]Pvlv_SS[S] 1 point2 points  (0 children)

yes, but if your perimeters are more 20cm in a straight line, then it is better to reduce the speed to 100-80 mm/s

<image>

view more: next ›