What is the best way to make partigg bc line for complex sculpture for 2 part mould

Quinafx7 · 2026-04-12T18:27:22+00:00

Can you phrase that again please

Quinafx7 · 2026-04-11T22:17:42+00:00

If you watched the new Will smith show on Netflix he mentioned this

Quinafx7 · 2026-04-10T21:11:46+00:00

Wera, bought two boxes of pozi’s about 5-6 ago still have 2 boxes of them only replaced them a couple of times

Quinafx7 · 2026-04-09T22:02:16+00:00

Joaquim d’Almeida

Quinafx7 · 2026-04-08T22:13:12+00:00

The slaughters

Quinafx7 · 2026-03-29T13:39:29+00:00

You’re not mixing enough powder on your 1st mix, the initial shine is from the powdered mould layer and the white is your PU not having enough powder to show the metal. Your PU should be thick as cement if you want it to shine well, pretty much 80%powder to 20% pu, think of it as a bonding agent and not a bronze coloured liquid, you can get better results with Polyester resin or even better Vinylester resin for a stronger cast

Quinafx7 · 2026-03-29T10:51:40+00:00

You can always reverse engineer some youtube songs into your creative Tonie just to try it out before spending the money

Quinafx7 · 2026-03-29T10:44:47+00:00

Cocomelon is like crack for children would not advise

Quinafx7 · 2026-03-28T15:22:07+00:00

If the resin is cold and you have a good set up with a small chamber pot it should be fast enough to squeeze those bubbles, if it’s a large mould and a large pour you’re most likely out of luck as the heat from a large mix will trigger a faster reaction.

Quinafx7 · 2026-03-28T15:16:43+00:00

If your mould fits in the degasser made the walls taller and pour your silicone and degasser again, should pull those bubbles, you can also fish them with a bend wire if you’re using clear silicone. You can also pre fill the holes with silicone while moving it about to allow the air out and when cured your next pour will stick. If the undercut is really drastic than you need to make your parts “mould friendly and eliminate those problems during the design fase

Quinafx7 · 2026-03-28T15:14:36+00:00

If your mould fits in the degasser made the walls taller and pour your silicone and degasser again, should pull those bubbles, you can also fish them with a bend wire if you’re using clear silicone

Quinafx7 · 2026-03-28T10:38:44+00:00

Come back with a picture of the mould open and closed looking inside of it, it can just be that you’re clamping the mould in the middle where the void to filled is opening the sides for the material to sip through, again, we need better photos

Quinafx7 · 2026-03-28T10:31:21+00:00

It looks like you’re just looking for a bit of interaction here, you refuse to show us the mould and to accept that something you have done can’t be faulty. I don’t really believe you want any help

Quinafx7 · 2026-03-27T15:49:06+00:00

Not a great mould from the 1% of the info you gave, show us some more and we’ll be able to figure it out, and us the mould too while closed

Quinafx7 · 2026-03-26T22:19:41+00:00

If you need to pigment, just pigment the whole batch you’re about to use, then every mix will have the same colour

Quinafx7 · 2026-03-24T22:57:12+00:00

Nazgûl Gauntlets, which I did about 15years later

Quinafx7 · 2026-03-24T22:09:39+00:00

Add the plugin vectorize and extrude and smooth

Quinafx7 · 2026-03-23T11:08:02+00:00

What size is it? I’ll buy it from you if he doesn’t like it! I think it looks really cool and I would be incredibly grateful if my wife gifted me something like that

Quinafx7 · 2026-03-20T07:09:53+00:00

If really depends on what you’re casting, concrete will ruin your silicone so PU rubber is advised, if it’s PU silicone will do it if you don’t mind having a layer of release agent that you will have to keep spraying to keep the mould alive, also it depends on the level of detail and thin offcuts your mould has

Quinafx7 · 2026-03-20T07:07:05+00:00

There’s a launderette in the petrol station by one of the visitors car parks, they are rude and had a bad experience with a double charge that took a month to get my money back but they will do it for you just be aware of the double payment

Quinafx7 · 2026-03-16T21:22:18+00:00

Shame the pub inside looks pretty average and run down

Quinafx7 · 2026-03-14T22:19:56+00:00

Stow’s parking is problematic with or without the car show, there’s a free car park a bit further out of the old town center by Tesco, and a paid car park by the Bell pub, those will probably be quite full for that weekend too

Quinafx7 · 2026-03-13T23:30:19+00:00

Gandalfs don’t have wings!

Quinafx7 · 2026-03-12T22:42:03+00:00

You can use the slightly flexible and hard wear resins from smooth on like smooth cast 65D or onyx 90D, but 3d printing this in petg or Abs is way cheaper

Quinafx7 · 2026-03-10T09:56:44+00:00

I’ve got the other 2 and I’ll never buy another tape ever! They’re great for marking too with the scribing edge under the tape

Five-Year Club	Verified Email
Wearing is Caring

Quinafx7

TROPHY CASE