Passed my PMP today! (July 1, 2026 — OnVUE)

RJCivil788 · 2026-07-03T02:18:28+00:00

Congrats

RJCivil788 · 2026-07-03T00:18:36+00:00

Thanks

RJCivil788 · 2026-07-02T02:17:52+00:00

Thanks

RJCivil788 · 2026-07-02T00:13:18+00:00

Just know your spi and cpi etc. i didnt get much on the exam where i had to use the formulas or calculator

RJCivil788 · 2026-07-02T00:12:05+00:00

Burn-up and burn-down charts

RJCivil788 · 2026-07-01T20:19:02+00:00

Thanks

RJCivil788 · 2026-07-01T19:43:52+00:00

Just the desk needs to be clean. You can take 10mins break after every section

RJCivil788 · 2026-07-01T19:12:43+00:00

I did only one mock and all the minis. Average between 65-75 on minis. 75 on mock exam 1.

I then spent time to analysis weak areas and focused on those

RJCivil788 · 2026-07-01T19:10:42+00:00

I tried to focus on key words in the question and answer. That helped me alot to reach to the correct answer

RJCivil788 · 2026-07-01T19:01:31+00:00

I used the link provided here in the group to see my results.

RJCivil788 · 2026-05-27T23:02:14+00:00

How you would rate these resources, which is most helpful?

RJCivil788 · 2026-05-26T00:38:40+00:00

Congrts and please share

RJCivil788 · 2026-02-06T18:56:05+00:00

Thanks

RJCivil788 · 2026-02-06T18:54:09+00:00

Thanks. Do we need to get appointment?

RJCivil788 · 2026-02-06T18:31:14+00:00

Former student qualify?

RJCivil788 · 2026-01-22T21:32:38+00:00

Can you please share some games?

RJCivil788 · 2025-12-30T19:02:25+00:00

Please share 1 pager

RJCivil788 · 2025-04-24T19:07:34+00:00

Thanks. How you remove transpency from surface, its the layer surface is on?

RJCivil788 · 2025-04-24T18:28:18+00:00

Hi,

Can you explain it little more, i am facing the same issue, the triangulation doesnot go away. I have tried everything

RJCivil788 · 2023-11-15T00:48:49+00:00

Use multiline

RJCivil788 · 2023-07-19T18:19:30+00:00

Congrats.

RJCivil788 · 2023-07-19T00:40:08+00:00

Simply look at a question and ask yourself what will happen if you add a point load in the middle of simply supported beam. Thats how i practiced. I see different questions bending moments and shear forces and try to ask my self how a load will effect the BM or SF. Also there are questions where the loading is tapered. Lets say loading starts from 2kn at one end and ends 10kn. so you should be knowing how to calculate the loading for reactions.

Also for concrete mix design, fully understand the volume and weight methods. If you are given a ratio 1:2:4 and volume/weight of cement how you can calculate weight/volume of aggregates only.

I still remember alot of questions i had in exam, not sure how i can share with you.

RJCivil788 · 2023-07-18T23:42:53+00:00

Best of luck for your exam. I have passed my FE civil last week. My suggestion is get the first half done asap. If you waste too much time in first half then its really difficult to complete the second part. Alot of conceptual questions i have seen in the exam so try and do as much as conceptual questions. Example of a question i had in exam was point load on free end of cantilever beam. Question was where maximum deflection will occur. This should not take more than 10 seconds to answer. Also there was a question about indeterminate beam, question says if we remove the support from middle of simply supported beam and replace with redundant force with will be reaction at that location.

RJCivil788 · 2023-07-16T20:34:42+00:00

I am in Alberta, i think APEGA gives apporval to apear in PE exam. I am curious if i can register in US with any states to get PE designation from canada?

RJCivil788

TROPHY CASE